If you are looking for a micro mixer circuit that create a simple, affordable, small and compact, and be usable versatile, must be this circuit. We can use to mix up to four input channels such as the microphone signal, FM Tuner, AUX and Other signals, As circuit shown in Figure 1. How it works. The input signal Input signal in each channel is entered through R1, R4, R6, R8, respectively, to potentiometer VR1-VR4. which is Adjustment value of Signal in each channel is the right size. Then is entered through a R2, R3, R5, R7 in together, and then pass through C1, R9 to input of IC1. – The IC1(TA7137) is amplifier a signal that was introduced all together, Until the output signal at pin 8 through C7. – The R14 and VR5 It is the adjust strength of the total output signal. – The C3, C2, D1, D2 are feed back circuit for control gain of circuit to has level constant output signal. – The LED L1 is a signal meter display that it flashes by the signal strength of the input voltage applied to the circuit.
Click here to download the full size of the above Circuit.
The detail parts. IC1_________________________________TA7137 PRE-AMPLIFIER(RECORDING OR PLAYING-BACK WITH ALC TRANSISTOR FOR TAPE RECORDER) D1, D2______________________________1N4148___75V 150mA Diodes L1__________________________________LED 2×5 mm R1, R4, R6, R8, R12____________________10K____1/4w Resistors R2, R3, R5, R7, R9, R14________________1K____1/4w Resistors R10_________________________________18K____1/4w Resistors R11_________________________________1K____1/4w Resistors VR1, VR2, VR3, VR4__________________5K-10K___Potentiometer VR5________________________________10K SW. C1, C8______________________________4.7uF 16V____Electrolytic Capacitors C2, C3______________________________0.0033uF 50V___Polyester Capacitor C4_________________________________30pF 63V___Polyester Capacitor C5_________________________________47uF 16V___Electrolytic Capacitors C6_________________________________100uF 16V____Electrolytic Capacitors C7_________________________________3.3uF 16V____Electrolytic Capacitors How to builds We install all the components on the PCB correctly completed. According to circuit in Figure 2. When finishedwe can install it in a box ready, for ease of use. In installed in the box, should be unloaded VR5 from PCB to hold separate. We can hold PCB to the box, with holding the potentiometer VR1-VR4 to box there. Then we remove the LED L1 out away, to hold at the box. And then we wiring to the equipment Jack...
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of....
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is....
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to....
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This....
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the....
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,....
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the....
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power....
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
characters left: