LOW COST SOLAR RADIO SPECTROGRAPH
The analog interface is a straightforward analog-to-digital converter that accepts the analog video output from the RF/IF board and converts it into a format that can be read by a PC games port. The joystick input of the games port effectively translates a resistance ranging from 0 to 100k ohms into a binary number from 0 to 255. The interface transistor presents itself to the PC as a variable resistance, with its value approximately proportional to the input voltage. Although the proportionality is not linear, it can still be utilized as a relative value or calibrated if a high-quality signal generator is available, though calibration is not strictly necessary. It is essential to configure the interface according to the output values received from the RF board. This setup process is detailed later. The eight data outputs of register one are employed to tune the radiospectrograph across the frequency band. These outputs are directed to the digital-to-analog converter interface to produce a voltage varying from 2 to 28 volts, which is applied to the tuning pin of the RF tuner. The two least significant bits of register three are used to select either the low band (VHF-Lo) or the high band (VHF-Hi) of the RF tuner. Asserting bit 0 selects VHF-Lo, while asserting bit 1 selects VHF-Hi. It is important to note that both bits 0 and 1 must not be asserted simultaneously. Additionally, the hardware inverts the values presented by the software to these two register bits. A small QBASIC program can be used to cycle the parallel port data byte from 0 to 255, which sets the maximum and minimum voltages output by the digital-to-analog converter (sweep generator). The program is named `DACTEST.BAS` and produces a sawtooth ramp. The code must be executed in DOS mode to ensure direct access to the parallel port without delays. When the parallel port is connected to the DAC and powered, the DAC output should be connected to an oscilloscope to observe the waveform, which should display a sawtooth pattern. The gain and offset controls in the DAC should be adjusted to ensure the waveform ramps between 2 volts minimum and 28 volts maximum, thus calibrating the DAC. The next major calibration involves the analog interface. The voltage applied to the input of this circuit from the VCR RF section depends on the characteristics of the intermediate frequency (IF) amplifier and the subsequent demodulator/detector. Older units typically use several discrete transistor amplifying stages to achieve the necessary high gain, with a discrete germanium diode serving as the detector. In such cases, when there is no input to the RF section (e.g., antenna terminals terminated by a 75-ohm resistor), the output from the diode detector is approximately zero. As the input signal increases, the output voltage may rise to one or two volts. More modern VCRs generally utilize an integrated circuit amplifier for both the IF amp and demodulator, often resulting in a resting voltage well above zero. The output DC level for the prototype SOLRAS is measured at a frequency of 70 MHz as a function of signal input to the antenna. A second program, `STIKTEST.BAS`, is used to test the calibration of the games port joystick input, displaying joystick input values on the screen. The first control to adjust is the Hi Set variable resistor.
The analog interface circuit operates as a bridge between the RF/IF board output and the PC games port, facilitating the conversion of analog signals into digital representations. The core of this interface is a transistor that acts as a variable resistor, adjusting its resistance based on the incoming voltage, which is critical for accurate signal processing. The non-linear relationship between input voltage and resistance must be accounted for during calibration, especially when interfacing with varying signal types from different RF sources.
The digital-to-analog converter (DAC) plays a pivotal role in tuning the RF tuner by generating a precise voltage output that corresponds to the desired frequency. The configuration of the DAC is essential, requiring careful adjustment of both the gain and offset to ensure the output voltage remains within the specified range. The calibration process involves connecting the DAC to an oscilloscope, where the generated waveform can be observed and adjusted accordingly.
The RF tuner’s operational bands are selected through register three, with a clear delineation between VHF-Lo and VHF-Hi. This selection mechanism is critical for ensuring that the tuner operates within the appropriate frequency range, avoiding potential signal interference or degradation. The inversion of bit values in the hardware necessitates careful programming to ensure the correct operational state is achieved.
The calibration of the analog interface must also consider the characteristics of the RF section of the VCR, particularly the type of amplifiers and detectors used. The output characteristics will vary significantly between older discrete component designs and modern integrated solutions, impacting the overall sensitivity and accuracy of the analog interface. The ability to measure and adjust these parameters is vital for maintaining signal integrity and achieving optimal performance in signal processing applications.
In summary, the design and calibration of the analog interface and associated components are critical for ensuring reliable operation and accurate signal conversion in applications involving RF signals and digital processing.The analog interface is a very simple analog to digital converter which accepts the analog video output of the RF/IF board and puts it into a form that can be read by a PC Games port. The joystick input of the games port essentially converts a resistance in the range 0 to 100k ohms into a binary number from 0 to 255.
The interface transistor looks to the PC as such a variable resistance, whose value is roughly proportional to the input voltage. The proportionality is not linear, but then neither is the receiver output. It can be used as a relative value, or it can be calibrated if a good quality signal generator is available. However, this is not necessary. It is necessary however, to set up the interface in accordance with the output values that it will receive from the RF board.
This process is described later. The eight data outputs of register one are used to tune the radiospectrograph across the frequency band. These are fed to the digital to analog converter interface as previously described to produce a voltage that varies from 2 to 28 volts.
This is applied to the tuning pin of the RF tuner. The two least significant bits of register 3 are used to select either low band (VHF-Lo) or the high band (VHF-Hi) of the RF tuner. Asserting bit 0 selects VHF-Lo, while asserting bit 1 selects VHF-Hi. Note that both bits 0 and 1 must not be asserted together. Also realise that the hardware does an inversion of the values presented by the software to these two register bits.
A small QBASIC program that cycles the parallel port data byte from 0 to 255 can be used to set the max and min voltages output by the digital to analog converter (sweep generator). The code is listed below. `File name DACTEST. BAS `DAC test `produces a sawtooth ramp dly = 0 `increase to increase step delay PRINT "Press ESC to end test" DO FOR i% = 0 TO 255 `value for DAC OUT 888, i% `output to LPT1 GOSUB Delay `wait a while NEXT i% `increment number LOOP WHILE INKEY$ <> CHR$(27) `press escape to exit END Delay: FOR zz = 0 TO dly NEXT zz RETURN This program must be run in DOS mode (not in a DOS window under WINDOWS).
Only in this mode are you sure of direct access to the parallel port without delays. With the parallel port connected to the DAC and power applied, connect the output of the DAC to an oscilloscope. Activate the program and observe the oscilloscope trace. It should be a sawtooth waveform. Adjust both the gain and the offset controls in the DAC to ensure that the waveform ramps between 2 volts minimum and 28 volts maximum.
The DAC is then calibrated. The next major calibration is the analog interface. The voltage applied to the input of this circuit from the VCR RF section will depend on the nature of the intermediate frequency (IF) amplifier and the subsequent demodulator/detector. If this is a really old unit it will probably employ several discrete transistor amplifying stages to achieve the required high gain.
The detector in these cases is usually a discrete germanium diode. When there is no input to the RF section (eg antenna terminals terminated by a 75 ohm resistor) the output from the diode detector will be approximately zero. As the input signal increases, the output voltage will rise to maybe a volt or two. A more modern VCR will usually employ an integrated circuit amplifier as both the IF amp and demodulator.
These often have a resting voltage well above zero. The table below indicates the output DC level for the prototype SOLRAS as a function of signal input to the antenna. This was measured at a frequency of 70 MHz. `Filename STIKTEST. BAS `Testing calibration of games port joystick input SCREEN 7 `large characters for visibility DO `set up an infinite loop a = STICK(0) `sample joystick A - X input LOCATE 12, 20 `then display in the PRINT a `middle of the screen LOOP WHILE INKEY$ <> CHR$(27) `ESCape to exit loop END The first control to adjust is the Hi Set variable resist
🔗 External reference
The analog interface circuit operates as a bridge between the RF/IF board output and the PC games port, facilitating the conversion of analog signals into digital representations. The core of this interface is a transistor that acts as a variable resistor, adjusting its resistance based on the incoming voltage, which is critical for accurate signal processing. The non-linear relationship between input voltage and resistance must be accounted for during calibration, especially when interfacing with varying signal types from different RF sources.
The digital-to-analog converter (DAC) plays a pivotal role in tuning the RF tuner by generating a precise voltage output that corresponds to the desired frequency. The configuration of the DAC is essential, requiring careful adjustment of both the gain and offset to ensure the output voltage remains within the specified range. The calibration process involves connecting the DAC to an oscilloscope, where the generated waveform can be observed and adjusted accordingly.
The RF tuner’s operational bands are selected through register three, with a clear delineation between VHF-Lo and VHF-Hi. This selection mechanism is critical for ensuring that the tuner operates within the appropriate frequency range, avoiding potential signal interference or degradation. The inversion of bit values in the hardware necessitates careful programming to ensure the correct operational state is achieved.
The calibration of the analog interface must also consider the characteristics of the RF section of the VCR, particularly the type of amplifiers and detectors used. The output characteristics will vary significantly between older discrete component designs and modern integrated solutions, impacting the overall sensitivity and accuracy of the analog interface. The ability to measure and adjust these parameters is vital for maintaining signal integrity and achieving optimal performance in signal processing applications.
In summary, the design and calibration of the analog interface and associated components are critical for ensuring reliable operation and accurate signal conversion in applications involving RF signals and digital processing.The analog interface is a very simple analog to digital converter which accepts the analog video output of the RF/IF board and puts it into a form that can be read by a PC Games port. The joystick input of the games port essentially converts a resistance in the range 0 to 100k ohms into a binary number from 0 to 255.
The interface transistor looks to the PC as such a variable resistance, whose value is roughly proportional to the input voltage. The proportionality is not linear, but then neither is the receiver output. It can be used as a relative value, or it can be calibrated if a good quality signal generator is available. However, this is not necessary. It is necessary however, to set up the interface in accordance with the output values that it will receive from the RF board.
This process is described later. The eight data outputs of register one are used to tune the radiospectrograph across the frequency band. These are fed to the digital to analog converter interface as previously described to produce a voltage that varies from 2 to 28 volts.
This is applied to the tuning pin of the RF tuner. The two least significant bits of register 3 are used to select either low band (VHF-Lo) or the high band (VHF-Hi) of the RF tuner. Asserting bit 0 selects VHF-Lo, while asserting bit 1 selects VHF-Hi. Note that both bits 0 and 1 must not be asserted together. Also realise that the hardware does an inversion of the values presented by the software to these two register bits.
A small QBASIC program that cycles the parallel port data byte from 0 to 255 can be used to set the max and min voltages output by the digital to analog converter (sweep generator). The code is listed below. `File name DACTEST. BAS `DAC test `produces a sawtooth ramp dly = 0 `increase to increase step delay PRINT "Press ESC to end test" DO FOR i% = 0 TO 255 `value for DAC OUT 888, i% `output to LPT1 GOSUB Delay `wait a while NEXT i% `increment number LOOP WHILE INKEY$ <> CHR$(27) `press escape to exit END Delay: FOR zz = 0 TO dly NEXT zz RETURN This program must be run in DOS mode (not in a DOS window under WINDOWS).
Only in this mode are you sure of direct access to the parallel port without delays. With the parallel port connected to the DAC and power applied, connect the output of the DAC to an oscilloscope. Activate the program and observe the oscilloscope trace. It should be a sawtooth waveform. Adjust both the gain and the offset controls in the DAC to ensure that the waveform ramps between 2 volts minimum and 28 volts maximum.
The DAC is then calibrated. The next major calibration is the analog interface. The voltage applied to the input of this circuit from the VCR RF section will depend on the nature of the intermediate frequency (IF) amplifier and the subsequent demodulator/detector. If this is a really old unit it will probably employ several discrete transistor amplifying stages to achieve the required high gain.
The detector in these cases is usually a discrete germanium diode. When there is no input to the RF section (eg antenna terminals terminated by a 75 ohm resistor) the output from the diode detector will be approximately zero. As the input signal increases, the output voltage will rise to maybe a volt or two. A more modern VCR will usually employ an integrated circuit amplifier as both the IF amp and demodulator.
These often have a resting voltage well above zero. The table below indicates the output DC level for the prototype SOLRAS as a function of signal input to the antenna. This was measured at a frequency of 70 MHz. `Filename STIKTEST. BAS `Testing calibration of games port joystick input SCREEN 7 `large characters for visibility DO `set up an infinite loop a = STICK(0) `sample joystick A - X input LOCATE 12, 20 `then display in the PRINT a `middle of the screen LOOP WHILE INKEY$ <> CHR$(27) `ESCape to exit loop END The first control to adjust is the Hi Set variable resist
🔗 External reference
Related Circuits
A radio camera on a model railway should transmit constantly while the train is moving and continue transmitting for a few minutes after the train stops. The design of a radio camera system for a model railway requires careful consideration...
The circuit in Figure 1 is an RS-232/485 converter that uses the transmitted signal itself to control the flow. The circuit uses MAX232 and MAX483 interface circuits, IC1 and IC2 from Maxim Integrated Products to convert between the ICs'...
Most small internal combustion engines commonly used in model building utilize glow plugs for starting. However, glow plugs operate at a voltage of 1.5 V, while components such as fuel pumps, starter motors, and chargers typically operate at 12...
A DC/DC step-up converter is suitable for use in battery-powered equipment. This converter can be employed to generate supply voltages for internal circuits. The DC/DC step-up converter, also known as a boost converter, is a critical component in various electronic...
Numerous miniature FM transmitter bug circuits are available online; however, this particular design is distinctive as it operates entirely on solar power, eliminating the need for a battery. The transmitter will function as long as sunlight is incident on...
A device for measuring daily insolation has been developed. The device is constructed using a PIC18F458 microcontroller and a 128MB Multimedia Memory Card (MMC). The insolation measurement device leverages the capabilities of the PIC18F458 microcontroller, which is known for...