Metal Detector Circuits
- Page 4-
The metal detector circuit shown here must represent the limits of simplicity for a metal detector, yet the design works surprisingly well. It uses just one 40106 hex Schmitt inverter IC, a capacitor and a search coil and of course the batteries. A lead from.... -
The working principle of this cheap and easy to build metal detector circuit consists in mixing two equal frequencies which causes a low-frequency interfer.... -
This homemade metal detector circuit will help you find objects composed of materials with relatively high magnetic permeability. It is not suitable for bu.... -
The heart of this diy metal detector circuit is the CS209A IC. The metal detector is built with one 100µH coil that has 40 mm in diameter and is made.... -
The original coil that came with the Heathkit project was preassembled at the factory. It had a diameter of around 15cm (6 inch). A larger (30cm, 12inch) coil can be made using the following data:.. -
If TIP32C (Q2) gets excessively hot, use an IRF9640 MOSFET instead. Experiment with different values for R6 to find the optimal value (I use a 390 ohm resistor). Temporarily substitute R6 for a trim potentiometer (470 or 1k) to find the optimal dumping.... -
The White`s Classic I was a very simple, easy to use machine, ideal for the entry-level detectorist to pick-up-and-go. It was a simple detector with no bells or whistles, only an on/off switch and a turn knob for a discriminator. It did not have much depth.... -
Various embodiments of the BB metal detector have been published, and it has been widely described in the press as a new genre. Instead of using a search and a reference oscillator as with BFO, or Tx and Rx coils as with IB, it uses two transmitters or.... -
Assemble the circuit on a perfboard or pcb except the inductor. Attach two long wires at the place of the inductor. Use a long rod and place the induc.... -
A simple home project can turn catastrophic fast if you come up against an electric cable, gas and water pipes, or your central heating system. With a handy metal detector you can check beforehand whether there are metal objects in a wall, ceiling or floor..... -
Most metal detectors work on the fact that metals in a magnetic field change the behaviour of the field. There are two general approaches to detect these changes. In one approach, an alternating current is provided to a transmit coil. A receive coil is used.... -
The device we then build will function as a metal detector that can scout out metal objects, such as coins, nails, keys such as car keys you may not be able to find, and even gold if you`re looking for in a beach (though this one may not have industrial.... -
When the receiver is tuned to a M. W. radio station the resulting feedback howl, caused by the transmitter can be set to alter, or appear when the coil and radio are above or near a metal object Here is a pictured of the search head. It is made from a.... -
A reasonably effective bfo (bifilar oscillator). Its performance is not comparable to more advanced commercial products, of course, but it still works. Anyway, during WWII metal detectors based on the same principle were utilized my combat engineers of many.... -
This metal detectors described in the example can be used to detect metal objects with high permeable magnetic substances. The working principle. The metal detector circuit is composed of the power circuit, sine wave oscillator, PLL phase-locked loop circuit.... -
The metal detector circuit consists of detection oscillator, reference oscillator, mixer and signal display, it is shown as Figure 8-70. The detection oscillator circuit is composed of the time base oscillator ICl, inductor Ll, potentiometer RPl, diode VDl.... -
That metal detector circuit uses LC single-tube oscillator circuit, it is shown as Figure 8-73. In the circuit, V is oscillating tube, L is the detection coil, Cl is the resonant capacitor. After turning on power switch S, the LC single-tube oscillator.... -
This example describes a metal detector which uses a PLL (phase locked loop) digital integrated circuit MCl4046, it can emit the alarm signal when detects metal objects, and it can determine detected material which is based on current meter`s instructions..... -
The metal detector circuit consists of the fixed frequency oscillator, mixer, detector, detection oscillator and power amplifier circuit, and the circuit is shown as the chart. Fixed frequency oscillator circuit consists of ceramic filter ZC, transistor VI.... -
The metal detector circuit is composed of the power circuit, sine wave oscillator, PLL phase-locked loop circuit and hybrid amplifying circuit, and the circuit is shown as the chart. Power circuit is composed of the batteries GBI, GB2, filter capacitors C1,.... -
The metal detector is composed of the probe oscillator, reference oscillator and audio amplifier and other components, and the circuit is shown as the chart. Probe oscillator consists of transistors VI, V2 and detection coil L1, capacitor C1 and so on..... -
The metal detector circuit consists of oscillator and sound-light alarm circuit, and the circuit is shown as the chart. Oscillator circuit consists of inductor L, capacitor C1, sensor switch integrated circuit IC1 (includes oscillator, detector and.... -
The metal detector circuit is composed of the probe oscillator, reference oscillator, oscillation signal processor, mixing amplifier and ammeter PA and other components, and the circuit is shown as the chart. Probe oscillator is composed of the oscillating.... -
The metal detector circuit is composed of the probe oscillator, PLL phase-locked loop circuit and the audio alarm circuit, and the circuit is shown as the chart. Probe oscillator is composed of the detection coil L, transistor VI, resistors RI ~ R3,.... -
A Coil Coupled Operation Metal Detector made from readily obtainable components and using an ordinary medium receiver as a detector.... -
This homemade metal detector circuit will help you find objects composed of materials with relatively high magnetic permeability. It is not suitable for buried coins discovery that is not sensitive enough but you can detect pirates treasures! The metal....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
A simple X-band radar detector is capable of indicating changes in rf radiation strength at...
This filter is used to reject or block a frequency or band of frequencies. These filters are...
Ul is an op amp used as a comparator. When the test probes are shorted together, resistors R1...
A laptop computer supply that has 9-V output, crowbar overvoltage protection, and operates i`rom...
The TINAH board shield, a printed circuit-board shield designed and built for Phys253 and first...
Building your own signal generator is a rite of passage for any analog DIYer, but it`s one I took...
Is possible to syncronize the leds so that first, the speakers are still playing aloud, and two,...
This remotely controlled watering system is both inexpensive and easy to expand. It is designed...
Nothing wrong at all with that setup IMO. I`ve an (older) Peltor FMT15 amp in my Golf. Works...
And the general high-frequency circuits, in the microwave band, the use of microstrip circuits to...
Circuit shown in Figure 3-147. To allow sufficient braking time, using the time relay KT (1 ~...
Fans can achieve remote control switch, speed control, remote control can also be achieved in...