Led circuits
The circuit below illustrates powering one or two LEDs from the 120-volt AC line using a capacitor to drop the voltage and a small resistor to limit the inrush current. Since the capacitor must pass current in both directions, a small diode is connected in parallel with the LED to provide a path for the negative half cycle and to limit the reverse voltage across the LED. A second LED with reversed polarity may be substituted for the diode, or a tri-color LED could be used, which would appear orange with alternating current. The circuit is fairly efficient and draws only about half a watt from the line. The resistor value (1K / half watt) was chosen to limit the worst-case inrush current to about 150 mA, which drops to less than 30 mA in a millisecond as the capacitor charges. This appears to be a safe value, as the circuit has been switched on and off multiple times without damaging the LED. The 0.47 µF capacitor has a reactance of 5600 ohms at 60 Hz, so the LED current is about 20 mA half-wave, or 10 mA average. A larger capacitor will increase the current, and a smaller one will reduce it. The capacitor must be a non-polarized type with a voltage rating of 200 volts or more. The lower circuit is an example of obtaining a low regulated voltage from the AC line. The zener diode serves as a regulator and also provides a path for the negative half cycle current when it conducts in the forward direction. In this example, the output voltage is about 5 volts and will provide over 30 milliamps with about 300 millivolts of ripple. Caution is advised when operating any circuits connected directly to the AC line. The LED traffic light circuit controls six LEDs (red, yellow, and green) for both north/south and east/west directions. The timing sequence is generated using a CMOS 4017 decade counter and a 555 timer. Counter outputs 1 through 4 are wired ORed using four diodes so that the (Red - North/South) and (Green - East/West) LEDs will be on during the first four counts. The fifth count (pin 10) illuminates (Yellow - East/West) and (Red - North/South). Counts 6 through 9 are also wired ORed using diodes to control (Red - East/West) and (Green - North/South). Count 10 (pin 11) controls (Red - East/West) and (Yellow - North/South). The time period for the red and green lamps will be four times longer than for the yellow, and the complete cycle time can be adjusted with the 47K resistor. The eight 1N914 diodes could be substituted with a dual 4-input OR gate (CD4072). The 555 circuit below is a flashing bicycle light powered with four C, D, or AA cells (6 volts). Two sets of 20 LEDs will alternately flash at approximately 4.7 cycles per second using the RC values shown (4.7K for R1, 150K for R2, and a 1µF capacitor). Time intervals for the two lamps are about 107 milliseconds (T1, upper LEDs) and 104 milliseconds (T2, lower LEDs). Two transistors are used to provide additional current beyond the 200 mA limit of the 555 timer. A single LED is placed in series with the base of the PNP transistor so that the lower 20 LEDs turn off when the 555 output goes high during the T1 time interval. The high output level of the 555 timer is 1.7 volts less than the supply voltage. Adding the LED increases the forward voltage required for the PNP transistor to about 2.7 volts, so that the 1.7-volt difference from supply to the output is insufficient to turn on the transistor. Each LED is supplied with about 20 mA of current for a total of 220 mA. The circuit should work with additional LEDs up to about 40 for each group, or 81 total. The circuit will also work with fewer LEDs, allowing it to be assembled and tested with just five LEDs (two groups of two plus one) before adding the others. (74HC138 or 74HCT138) can be used to generate the popular "Night Rider" display. A Schmitt Trigger oscillator provides the clock signal for the counter, and the rate can be adjusted with the 500K potentiometer. Two additional Schmitt Trigger inverters can be employed to enhance the circuit's functionality.
The circuit design effectively utilizes a capacitive dropper to power LEDs directly from the high-voltage AC mains, ensuring that the components are rated appropriately to handle the voltage and current levels. The use of a non-polarized capacitor is crucial for bidirectional current flow, while the inclusion of a diode or a second LED safeguards against reverse voltage, protecting the primary LED from potential damage. The choice of a 1K resistor is a calculated decision to balance the initial inrush current with the steady-state operation, ensuring the longevity of the LED.
The traffic light circuit exemplifies a practical application of sequential logic using the CMOS 4017 counter, which allows for a visually effective and safe traffic control system. The timing adjustments facilitated by the 555 timer and the resistor provide flexibility in operation, allowing for customization based on specific requirements.
Moreover, the bicycle light circuit demonstrates the versatility of the 555 timer in low-power applications, where the use of transistors allows for higher current loads beyond the timer's native capabilities. The design is modular, permitting easy testing and expansion, while the Schmitt Trigger components ensure reliable operation of the clock signal, providing stable timing for the light sequences. Overall, this circuit showcases a range of practical electronic design techniques suitable for various applications in LED lighting and control systems.The circuit below illustrats powering a LED (or two) from the 120 volt AC line using a capacitor to drop the voltage and a small resistor to limit the inrush current. Since the capacitor must pass current in both directions, a small diode is connected in parallel with the LED to provide a path for the negative half cycle and also to limit the reve
rse voltage across the LED. A second LED with the polarity reversed may be subsituted for the diode, or a tri-color LED could be used which would appear orange with alternating current. The circuit is fairly efficient and draws only about a half watt from the line. The resistor value (1K / half watt) was chosen to limit the worst case inrush current to about 150 mA which will drop to less than 30 mA in a millisecond as the capacitor charges.
This appears be a safe value, I have switched the circuit on and off many times without damage to the LED. The 0. 47 uF capacitor has a reactance of 5600 ohms at 60 cycles so the LED current is about 20 mA half wave, or 10 mA average.
A larger capacitor will increase the current and a smaller one will reduce it. The capacitor must be a non-polarized type with a voltage rating of 200 volts or more. The lower circuit is an example of obtaining a low regulated voltage from the AC line. The zener diode serves as a regulator and also provides a path for the negative half cycle current when it conducts in the forward direction. In this example the output voltage is about 5 volts and will provide over 30 milliamps with about 300 millivolts of ripple.
Use caution when operating any circuits connected directly to the AC line. The LED traffic Light circuit controls 6 LEDs (red, yellow and green) for both north/south directions and east/west directions. The timing sequence is generated using a CMOS 4017 decade counter and a 555 timer. Counter outputs 1 through 4 are wire ORed using 4 diodes so that the (Red - North/South) and (Green - East/West) LEDs will be on during the first four counts.
The fifth count (pin 10) illuminates (Yellow - East/West) and (Red - North/South). Counts 6 through 9 are also wire ORed using diodes to control (Red - East/West) and (Green - North/South). Count 10 (pin 11) controls (Red - East/West) and (Yellow - North/South). The time period for the red and green lamps will be 4 times longer than for the yellow and the complete cycle time can be adjusted with the 47K resistor.
The eight 1N914 diodes could be subsituted with a dual 4 input OR gate (CD4072). The 555 circuit below is a flashing bicycle light powered with four C, D or AA cells (6 volts). Two sets of 20 LEDs will alternately flash at approximately 4. 7 cycles per second using RC values shown (4. 7K for R1, 150K for R2 and a 1uF capacitor). Time intervals for the two lamps are about 107 milliseconds (T1, upper LEDs) and 104 milliseconds (T2 lower LEDs). Two transistors are used to provide additional current beyond the 200 mA limit of the 555 timer. A single LED is placed in series with the base of the PNP transistor so that the lower 20 LEDs turn off when the 555 output goes high during the T1 time interval.
The high output level of the 555 timer is 1. 7 volts less than the supply voltage. Adding the LED increases the forward voltage required for the PNP transistor to about 2. 7 volts so that the 1. 7 volt difference from supply to the output is insufficient to turn on the transistor. Each LED is supplied with about 20 mA of current for a total of 220 mA. The circuit should work with additional LEDs up to about 40 for each group, or 81 total. The circuit will also work with fewer LEDs so it could be assembled and tested with just 5 LEDs (two groups of two plus one) before adding the others. (74HC138 or 74HCT138) to generate the popular "Night Rider" display. A Schmitt Trigger oscillator provides the clock signal for the counter and the rate can be adjusted with the 500K pot.
Two additional Schmitt Trigger invert 🔗 External reference
The circuit design effectively utilizes a capacitive dropper to power LEDs directly from the high-voltage AC mains, ensuring that the components are rated appropriately to handle the voltage and current levels. The use of a non-polarized capacitor is crucial for bidirectional current flow, while the inclusion of a diode or a second LED safeguards against reverse voltage, protecting the primary LED from potential damage. The choice of a 1K resistor is a calculated decision to balance the initial inrush current with the steady-state operation, ensuring the longevity of the LED.
The traffic light circuit exemplifies a practical application of sequential logic using the CMOS 4017 counter, which allows for a visually effective and safe traffic control system. The timing adjustments facilitated by the 555 timer and the resistor provide flexibility in operation, allowing for customization based on specific requirements.
Moreover, the bicycle light circuit demonstrates the versatility of the 555 timer in low-power applications, where the use of transistors allows for higher current loads beyond the timer's native capabilities. The design is modular, permitting easy testing and expansion, while the Schmitt Trigger components ensure reliable operation of the clock signal, providing stable timing for the light sequences. Overall, this circuit showcases a range of practical electronic design techniques suitable for various applications in LED lighting and control systems.The circuit below illustrats powering a LED (or two) from the 120 volt AC line using a capacitor to drop the voltage and a small resistor to limit the inrush current. Since the capacitor must pass current in both directions, a small diode is connected in parallel with the LED to provide a path for the negative half cycle and also to limit the reve
rse voltage across the LED. A second LED with the polarity reversed may be subsituted for the diode, or a tri-color LED could be used which would appear orange with alternating current. The circuit is fairly efficient and draws only about a half watt from the line. The resistor value (1K / half watt) was chosen to limit the worst case inrush current to about 150 mA which will drop to less than 30 mA in a millisecond as the capacitor charges.
This appears be a safe value, I have switched the circuit on and off many times without damage to the LED. The 0. 47 uF capacitor has a reactance of 5600 ohms at 60 cycles so the LED current is about 20 mA half wave, or 10 mA average.
A larger capacitor will increase the current and a smaller one will reduce it. The capacitor must be a non-polarized type with a voltage rating of 200 volts or more. The lower circuit is an example of obtaining a low regulated voltage from the AC line. The zener diode serves as a regulator and also provides a path for the negative half cycle current when it conducts in the forward direction. In this example the output voltage is about 5 volts and will provide over 30 milliamps with about 300 millivolts of ripple.
Use caution when operating any circuits connected directly to the AC line. The LED traffic Light circuit controls 6 LEDs (red, yellow and green) for both north/south directions and east/west directions. The timing sequence is generated using a CMOS 4017 decade counter and a 555 timer. Counter outputs 1 through 4 are wire ORed using 4 diodes so that the (Red - North/South) and (Green - East/West) LEDs will be on during the first four counts.
The fifth count (pin 10) illuminates (Yellow - East/West) and (Red - North/South). Counts 6 through 9 are also wire ORed using diodes to control (Red - East/West) and (Green - North/South). Count 10 (pin 11) controls (Red - East/West) and (Yellow - North/South). The time period for the red and green lamps will be 4 times longer than for the yellow and the complete cycle time can be adjusted with the 47K resistor.
The eight 1N914 diodes could be subsituted with a dual 4 input OR gate (CD4072). The 555 circuit below is a flashing bicycle light powered with four C, D or AA cells (6 volts). Two sets of 20 LEDs will alternately flash at approximately 4. 7 cycles per second using RC values shown (4. 7K for R1, 150K for R2 and a 1uF capacitor). Time intervals for the two lamps are about 107 milliseconds (T1, upper LEDs) and 104 milliseconds (T2 lower LEDs). Two transistors are used to provide additional current beyond the 200 mA limit of the 555 timer. A single LED is placed in series with the base of the PNP transistor so that the lower 20 LEDs turn off when the 555 output goes high during the T1 time interval.
The high output level of the 555 timer is 1. 7 volts less than the supply voltage. Adding the LED increases the forward voltage required for the PNP transistor to about 2. 7 volts so that the 1. 7 volt difference from supply to the output is insufficient to turn on the transistor. Each LED is supplied with about 20 mA of current for a total of 220 mA. The circuit should work with additional LEDs up to about 40 for each group, or 81 total. The circuit will also work with fewer LEDs so it could be assembled and tested with just 5 LEDs (two groups of two plus one) before adding the others. (74HC138 or 74HCT138) to generate the popular "Night Rider" display. A Schmitt Trigger oscillator provides the clock signal for the counter and the rate can be adjusted with the 500K pot.
Two additional Schmitt Trigger invert 🔗 External reference
Related Circuits
Circuits that generate PWM pulses typically translate a resistor value into a change in duty cycle. While this method is convenient, there are instances where a voltage-controlled PWM generator is required. Although microcontrollers can produce a variety of PWM...
A 4-position slide switch is utilized to activate different colored LEDs based on its position. Additionally, it is required to adjust the output frequency of a 555 timer operating in astable mode to drive a piezo buzzer. The challenge...
The circuit is depicted in Figure 1, while the electrical schematic diagram is presented in Figure 2. The AC voltage of 220V is reduced by components C3 and R3. The diodes VD1 and VD2 rectify the voltage, and capacitors...
A school drama required lamps that automatically turned on and off in sync with the spotlights. The lamp switching system needed to be wireless, durable, reliable, simple, and cost-effective. With the stage and spotlights turned off, minimal light reaches...
A project called LED Flasher that sequentially flashes LEDs one by one. There is a query regarding the project, and any simple explanation would be greatly appreciated. A reference image or a link can be used for additional context. The...
This design concept outlines a 12-V DC to 5-V DC (±5%) switched-mode power supply (SMPS). The supply utilizes a 12-V input derived from an array of four 3-V DC, 40-mA solar cells connected in series. The proposed switched-mode power supply...