Siren Circuits
- Page 2-
This circuit provides a good siren noise suitable for warding off robot-predators! Change the pitch by adjusting R2, and R5... -
This circuit is intended for children fun, and can be installed on bicycles, battery powered cars and motorcycles, but also on models and various games and toys. With SW1 positioned as shown in the circuit diagram, the typical dual-tone sound of Police or.... -
With this circuit we can create a altered sound of siren. The oscillator IC1a-b is constituted by two gates NAND, oscillating in very low frequency. This oscillation drive the IC2, that is a electronic switch, which opens and closes in the rythm of.... -
This project is built on the third section of the PC board, identified by "SIREN" and "Project 5." You will notice the similarity between this circuit and the LED FLASHER circuit from project 2. The only differences are the LED has been removed and the 22R.... -
Voltage is applied to the chip via pins 14 and 7 so that when power is applied to the project, the high and low frequency oscillators will come into operation to produce a wailing sound from the piezo. The high frequency oscillator is the only tone sent to.... -
This circuit produces a sound similar to a factory siren. It makes use of a 555 timer Ic used as an astable multivibrator of a center frequency of about 300Hz. The frequency is controlled by the pin 5 of the IC. When the supply is switched ON, the.... -
This circuit produces a sound similar to the police siren. It makes use of two 555 timer ICs used as astable multivibrators. The frequency is controlled by the pin 5 of the IC. The first IC (left) is wired to work around 1Hz. The 47uF capacitor is.... -
This blog shows project documentations of various projects done by members of association of experimental electronics. Some projects are very easy and suitable for beginners, some are only for more advanced solderers. The core parts of this sequencer were.... -
Operation of the circuit. Circuit is divided into three parts: low frequency production. The manufacturing high frequency and extension of production low frequency is obtained from IC1 connected to astable multi vibrator circuit frequency is set by R1, C2.... -
Browse » home » alarm » circuit » explanation » latest » schematic » siren » wailing » with » latest Wailing Alarm Siren circuit Schematic with explanation *The Loudspeaker LS and the resistor marked Rx should be together 75 ohms. If you have a standard.... -
The 555 on the right is wired as an alarm sound generator and the second 555 timer on the left is a 1 Hz astable multivibrator. The output of the left timer is to modulate the frequency of the right timer. This process will cause the right timers frequency.... -
This circuit is a double tone Police sound and Single tone old ambulance sound. This circuit is usually installed on a on battery powered cars, motorcycles, ... -
Here is police tone circuit of siren. this simple and very easy to make it. vr 1 and vr 2 for change delay sound of siren. simple and easy. if sound output not... -
Operation of the circuit. Circuit is divided into three parts: low frequency production. The manufacturing high frequency and extension of production low... -
Here the circuit diagram of electronic siren based NE555. This circuit produces a sound like factory siren. It applies a 555 timer IC which is utilized as an astable multivibrator of a center frequency of about 300Hz. The frequency is controlled by the pin 5.... -
The circuit is built around popular CMOS oscillator-cum-divider IC 4060 and small audio amplifier LM386. IC 4060 is used as the multitone generator. A 100 H inductor is used at the input of IC 4060. So it oscillates within the range of about 5MHz RF. IC 4060.... -
The circuit described here can create three different US-style` siren sounds: police, ambulance and fire engine. The desired sound can be selected using switch S1. The circuit can be used in toys (such as model vehicles), as part of an alarm system, and in.... -
Police Siren circuit diagram. This circuit produces a sound similar to the police siren. It makes use of two 555 timer ICs used as... -
Assortment of Siren Circuits. This month I am making 3 different types of siren circuits based on the 555 timer. The first circuit simulates the siren of a British police car. It uses two... -
Siren Circuit. This circuit is to generate sound siren when S1 is pressed and increate sound frequency because charged C1, S1 is released when the frequency decreated... -
One-IC two-tones Siren. Double-tone Police sound. Single-tone old ambulance sound. Circuit diagram: Parts: R1,R3 470K 1/4W Resistors R2 680K 1/4W... -
The 555 on the right is wired as an alarm sound generator and the second 555 timer on the left is a 1 Hz astable multivibrator. The output of the left timer is to modulate the frequency of the right timer. This process will cause the right timers frequency.... -
Function of the Two Siren Sound Circuit that is using IC 555. Siren Circuit is separated into three parts: low frequency production. The manufacturing shrill frequency and annex of production low frequency is obtained from IC1 connected to astable multi.... -
The employment of the circuit IC1 which build survive astable multi vibrator circuit. self-control gesticulate frequency low origin comes exposed the way pin 3 take approximately 1 Hz by frequency charge with the intention of s were fixed by the value, R1,.... -
The 555 on the right is wired as an alarm sound generator and the second 555 timer on the left is a 1 Hz astable multivibrator. The output of the left timer is to modulate the frequency of the right timer. This process will cause the right timers frequency....
-
This circuit is a circuit that sounds a siren-like sound of ambulance sirens. This circuit is different to an ambulance siren circuit generally, is to use transistors instead of IC 555. Which allows economical and easy to tailor a network. Operation of the.... -
The second circuit simulates the siren of an American police car. It uses two 555 timers in the circuit. The 555 on the right is wired as an alarm tone generator and the second 555 timer on the left is wired as a low frequency astable timer which generates a.... -
The heart of the circuit is the two transistor flasher with frequency modulation applied to the base of the first transistor. When the pushbutton is depressed, the frequency of oscillation climbs to a peak and when the button is released, the frequency.... -
This is a simple siren sound that high power output and very noisy. ICs, Digital ICs are easy to use number CD4046 Inverter circuit and four transistor power increase current out to horn speaker 20 watt 4ohm 8ohm. Operation of the circuit when the circuit is.... -
The heart of the circuit is the two transistor flasher with frequency modulation applied to the base of the first transistor. When the pushbutton is depressed, the frequency of oscillation climbs to a peak and when the button is released, the frequency.... -
This multitone electronic siren is useful for burglar alarms, reverse horns, etc. It produces five different audio tones and is much more earcatching than a single-tone siren. The circuit is built around popular CMOS oscillator-cum-divider IC 4060 and small....
Neighbour Categories
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Its frequency depends on the capacitance of the vary cap diode. The center frequency is changed...
This receiver is a modification of Charles Wenzel`s Two Transistor Reflex Radio. Instead of a...
Not drive a solenoid directly from your Arduino. It requires more current than you can provide...
We`ve all had occasion to be annoyed at inconsiderate dog owners whose animals relieve themselves...
This small transmitter uses a hartley type oscillator. Normally the capacitor in the tank circuit...
There are not many AM transmitters that are easier to build than this one because the inductor is...
In this diagram, look to see if you have battery voltage at these points. You don`t have to check...
Leo Esaki invented the tunnel diode in 1957 while working at Sony (Tokyo Tsushin Kogyo at the...