Vacuum-Tube Valves Circuits
- Page 5
-
A regenerative radio works by feeding back a small amount of amplified output of the detector back into the input. Thus it achieves sensitivity far beyond what only a detector could alone. This simple regen radio uses a single tube as it`s detector and....
-
-
A Pair of Push-Pull Class A, Ultra Linear Mono Block Tube Amplifiers that can be used with several different vacuum tubes including KT77 / 6L6GC / KT88 with a 12SL7 driver and 6NO30 tubes...
-
-
-
-
The common wiring method had one side of the line cord going to a pin on the rectifier tube and the other side going to one terminal of the on/off switch. The other terminal of the on/off switch went to chassis. Suppose you plugged it in so the chassis was....
-
-
It`s a power amplifier configuration that was developed in the 1950s. It is called a circlotron because the original idea diagram was drawn as a circle. The best I can do with my graphics program is to show it as a bridge. It`s promise is very low....
-
You see that the feedback is DC coupled, not through a capacitor, from the plate of the second triode to the cathode of the first. An earlier design used AC coupled feedback. This version was unstable at low frequencies. Bode analysis showed that a 3....
-
You may be wondering why I am using four tubes. The reason is to get 50 watts without pushing them right to their limit. My tube manual gives two setups for EL34s in ultra linear. Both require a 6 k ohm transformer. Both setups use exactly the same voltages....
-
Vacuum tube electronic circuits operate from comparatively high DC voltages (150 to 600 volts). The Electric Utility supplies 120 volts AC. We have studied transformers and, therefore, we know that the 120 vAC line voltage could be stepped up to the....
-
This stage may be driven by another resistance coupled amplifier stage in which case the resistor on the left labeled RC is RCf for the previous stage. The resistor on the right labeled RCf is the grid resistor of the next or following stage. The resistor....
-
-
-
-
The very first form of radio communication was radio telegraphy, as opposed to wired telegraphy. The telegraph key turns the transmitter on when it is closed and off when open. The operator taps out the message in a long and short, dashes and dots, code and....
-
-
-
-
-
Quote: Originally Posted by rntlee The only schematic of this amp I`m aware of is this one(I got it from Song @ Canadian Hifi Online):Attachment 238521 It`s possible ....
-
-
The VCO presented here is a direct derivative of the original oscillator invented by Friedrich Trautwein in 1932. And it perfectly demonstrates why I`m so cynical about the music world: the Mixtur-Trautonium oscillator was a true VCO, invented at a time when....
-
The RCA-83 rectifier makes use of 5VAC for the filaments. The heaters for the 5687 tubes are provided from a full bridge of MUR860 diodes, followed by 5 x 10, 000uF Elna caps. 830mA of current regulation is supplied using a LM317 regulator plus a 1R5....
-
Miniature vacuum tubes with cathodes of high-field-emitting carbon nanotubes are currently under study at Agere Systems in Murray Hill, NJ. A triode with amplification factor of 4 has been constructed, with an anode-cathode spacing of 220 µm, and a pentode....
-
The DS2422 temperature/data logger combines the core functions of a fully featured data logger in a single chip. It includes a Temperature Sensor Real-Time Clock (RTC), memory, 1-Wire Interface and serial Interface for an Analog-to-digital converter (ADC),....
-
Power demand in portable designs CAN require in some specific application more than 1 A. A method consists in paralleling two DC to DC converters on the same load instead of placing a single higher current converter with lower switching frequency. This....
-
The PCD3360 is a CMOS integrated circuit, designed to replace the electro-mechanical bell in telephone sets. It meets most postal requirements, with selectivity of output Tone sequences and input ringer frequencies. Output signals for a loudspeaker or for a....
-
-
even if I didn`t read thoroughly nice one almost enough xformers , but certainly not enough shunt regs....
-
This is a very nice amplifier design and it is very difficult to improve it. I am glad about the results because that's a very good way to verify my 6DJ8 and 6L6GC Spice models, like I tell you before, the 6L6GC and 807 have very close caracteristics and....
-
Build a preamp that I want to use to take a 1/4" keyboard line level signal and drive a Leslie 147 amplifier with it. I want to build the preamp using a 12AX7 and 12BH7 based on the design of a Hammond Organ preamp. Here is the schematic to the Hammond AO-28....
-
Hi everyone, just wondering as I am about to build my first tube amplifier is the attached design o.k. and also does anyone know a suitable....
-
i have a fujiya fl-555 (schematic attached) that i am having problems with. the recorder`s volume is very low even at maximum setting. it was working....