Switching Circuits
- Page 13-
This circuit prevents surges. From the opening is switched off or power failure. The damage to electrical appliances. The circuit will switch to use a short.... -
This 555timer clap switch circuit electronic project is designed using some common electronic parts. This 555 timer clap switch circuit electronic project operates from a distance of up to 10 meters from the microphone. Signal from microphone is amplified by.... -
The TDA1029 is a dual operational amplifier (connected as an impedance converter) each amplifier having 4 mutually switchable inputs which are protected by clamping diodes. Signal-sources switch can be made in various mods : Electronic parts required by this.... -
A very simple 3. 25W CV/CC charger can be designed using LinKSwitch | family IC manufactured by Power Integrations. This electronic circuit project is designed to provide a 5 volts output at a maximum current of 650mA. This 3. 25W CV/CC charger, needs to be.... -
This Light Dark switch activated relay circuits schematics are the simplest electronic circuits that can help you to activate other electronic device at the light or dark. This Light Dark switch activated relay circuits are very simple and require one.... -
This sensor switch circuit has nine channels and consist of only three integrated circuits and some resistors. Due to high input impedance, 74HC147 allows to use of 4. 7 M resistors to create a logic level "high" to sensor inputs. When one sensor is touched,.... -
This touch sensor switch can is designed using inverters (N1, N2)and some common electronic components. In standby state at the entrances of N1 there is a signal produced by oscillator N3/N4. At the touch sensor hand capacity forms a bridge to the ground for.... -
From ages electron-magnetic relays are being used as switches to control high voltage devices. But, because of their bulky size and noise (both electrical and mechanical) people started using TRIAC with opto-coupler as better alternative. Above circuit uses.... -
Infrared Remote Control Switch Circuit Remote controls, specially cordless type, are very popular nowadays. Here is a simple and.... -
Here is a touch switch that can be used to drive LEDs, relays etc through a buffer transistor stage. It may be built around any CMOS inverter chip .. -
VCR Camera Video Detector Switch Controller Circuit This video detector switch controller circuit uses the video output from a VCR or camera to.... -
For those who are lazy like me, turn on or off the bedroom light without getting out of bed, simple clap your hands is amazing. Thinking about it I projected one for me. Several projects of clappers can be found on the Internet, and most of them do not use.... -
This electronic timer switch will ON your light for 100 seconds, OFF for another 100 seconds and ON again for 100 seconds after an hour of powering up the circuit. Good home project to build .. -
This temperature switch uses a few discrete components to trigger a buzzer when the temperature of the surrounding increases. Suitable for use as a simple fire alarm indicator .. -
The sustain pedal is also known as the Damper Pedal. When operated it sends out a controller value of CC64. When the pedal is pressed ON the unit outputs a value of 127, when released OFF the unit outputs a value of 0. Tone-generators without the.... -
Hello, I assembled a circuit on a breadboard which is separated in 2 parts: the right part is for generating an alarm which wails. the left part is.... -
Hi, I`m trying to build a circuit with two key switches, where both key switches need to be closed for the current to go through. I am trying to use a .... -
This PIN diode rf switch is the ideal antenna switch for VHF and UHF and work with the PIN diodes which are special high frequency switching diodes with ve.... -
In this halogen switch circuit we use a FET transistor because the current is dependent of the FET`s gate voltage. The maximum gate voltage is 12V, so this circuit is adequate for 12 volt lamps. R1 value is 100 k © for 6V and 470 k © for 12V. You can use.... -
Here is the circuit of an ultra sensitive IR receiver that can be used to switch on various AC devices through an IR transmitter. It uses the Photo transis.... -
SFH505A made by Siemens combine infrared diode receiver, amplifier, demodulator and a filter band pass for minimizing interferences. This circuit works tog.... -
A Simple Infrared controlled Switch. It can be operated using the TV remote handset. The Load can be any AC operated device which can be connected to the relay. The load turns on for three minutes then goes off. It can be used to switch on the lamp in the TV.... -
This time delay switch circuit is useful to switch on an AC load such as lamps after the delay of three minutes. This protects the load from inrush current and transients at power on which may be detrimental to the device. The time delay switch is directly.... -
Here is a simple toggle switch that can be operated through sound signals such as whistle or clap. The output of the toggle remains either low or high unti.... -
Install the PIR module hanging from a 3 metre high mast (to cover 10 metre radius area) and connect its supply and relay terminals to our finished and enclosed circuit, observing right polarity. A 4-core screened cable can be used for this interconnection..... -
A great collection of touch switch circuits. A touch switch is an electronic device that enables us to control a circuit by simply touching a sensor. The circuit as you can see from its diagram is very simple and only uses 8 components. The heart of the.... -
Moderately priced Passive Infrared PIR Sensor modules are now widely available. By using these readymade and pre-configured PIR sensors, even an average el.... -
This analog switch circuit is designed to switch on or off and analog line. it consists of two analog switches in IC form that are controlled by two pushbu.... -
The power switch with infrared proximity sensor is intended for the recognition of obstructions at distances of a few millimetres to a few centimetres. Thi.... -
This humidity controlled switch circuit turns on and off an electrical load (for example a heater) depending on the moisture content of the surrounding air....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Schematic Diagramis a layout of symbols and and connection of every electronic components circuit...
This audio amplifier designed uses two LM3886 per channel, in parallel circuit, based on the...
Car radio application using class AB Audio Power Amplifier usually has TDA7360 inside it. It is...
This simple circuit has helped me out on many occasions. It is able to check transistors, in the...
The circuit is a remotely operated DTMF telephone. The circuit can be used to change up to 9...
For some ten years Texas Instruments have been developing solid state speech technology with the...
This 1000 watt power inverter circuit diagram based on MOSFET RF50N06. If you want more power...
A simple calling bell circuit that can be used in small offices to call the office boy using an...
Circuit shown in Figure 3-159. The circuit uses complement each other three times and three...