Switching Circuits
- Page 14-
Here is an ultra simple automatic light switch circuit for bedrooms. After construction, connect the input terminals of this circuit in parallel to the int.... -
As the name indicates, the step switch selector circuit is intended to choose one of up to four analogue switches, which it does with the aid of some less.... -
When loading a battery during the day from a solar panel it can be partially discharging through the panel after nightfall. This solar panel power switch circuit replaces the diode and connects the panel to battery through a relay contact. When the voltage.... -
This light sensitive automatic light switch circuit is intended to be connected at the main 220V supply. The circuit will connect a 220V lamp at the nightf.... -
This light sensor switch circuit allows the automatic connection of a lamp when the light is low (at nightfall) and will maintain the lamp ON for a certain period of time. From the moment that T4 and T5 are opened, relay`s LED start to light and powers the.... -
The light activated switch circuit can be used for switching OFF a particular lamp or group of lamps in response to the varying ambient light levels. The u.... -
This is a simple update to Mr. Hareendran`s PIR Sensor Security Light circuit. It has a shortcoming limits the relay voltage to approximately 3. 3V. While this may function with some 5V relays, it will not function with all. The nature of an emitter follower.... -
The circuit is a precision integrated temperature sensor type LM35 (IC1), which provides an accurately linear and directly proportional output in mV, over the zero to +155 degrees C temperature range. This can be used as part of fire smoke detectors but do.... -
With this sound activated switch, control by sound may be very useful, not just on a robot but also for a bit of home automation, for example a sound-activ.... -
This automatic door light switch circuit turns ON a lamp when a door is opened then turns it OFF when the door is opened again. The working principle of th.... -
With this whistle light switch you can turn on and off the lighting installation. The main part of this circuit is the UM3763 IC, produced by UMC. The piezo-ceramic buzzer is used here as a microphone and when it receives a tone frequency between 1. 2 kHz.... -
Simple, highly sensitive capacitive ON/OFF switch pads change the state of a latch and turn on an LED without requiring actual physical human contact. The pad may be insulated. A range of 12mm is easily obtained and sensitivity is adjustable. Central is the.... -
This kind of sensor switch is suitable for making touch operated bells, buzzers of small toys which operate for a small time and then switch off automatically. The input impedance of the trigger is very high and the touch sensor switch can be triggered by.... -
Based on NE555 this circuit turns on and off the IC output by a momentary switch. In other words it works as a mechanical latching relay, but the circuit backs to the start condition when you switch off the power supply. This feature is often required in.... -
It is often required to switch electrical appliances from a distance without being a direct line of sight between the transmitter and receiver. As you may.... -
My modification, i have two trigger coils , two power coils, one reed switch. The wheel is 4 north pole magnet, it generates 9 radiant pulses per.... -
Thank you very much I will try that. @StevanC What do you think, are we making some progress or should we stick to your design scratchrobot.... -
Light Sensitive Staircase Switch with Triac , Operation of the third circuit is much similar except that it has photo sensitivity. The circuit is shown in Schematic When there is no sufficient l.... -
The 555 circuit can be re-triggered if the input is held low longer than the output pulse. To prevent this happening, I have included a further timing circuit comprised of the 1Meg resistor and 47n capacitor. Normally, the 47n capacitor is discharged via the.... -
This is a good Electrical project report on Infrared Remote Control On/Off Switch and was Submitted in partial fulfillment of the requirements for the award of the degree of Bachelor of Engineering in Electrical Engineering and is used to switch on/off the.... -
I decided to throw together a schematic of how the OEM AUX switch should be wired, and print it so that when I install the wiring I would have a handy reference. Figured I would post it. Here is another breakdown of the switch pins, keeping in mind that.... -
Usually a single telephone is connected to a telephone line. If another telephone is required at some distance, a parallel line is taken for connecting the other telephone. In this simple parallel line operation, the main problem is loss of privacy besides.... -
Each audio/video output can be switched to any of the 8 inputs, separately. One module drives one audio/video output and has a 34-pin connector to plug into the system interface. You can use video OPA-s on the 4051 output instead. Note that you can get full.... -
This simple circuit can be wired into your headlight switch to provide automatic switching between high and low beam headlights when there is oncoming traffic. Simple electronics project with circuit diagram.... -
This is a Universal version of the Four-Digit Alarm Control Keypad. I have modified the design to free up the relay contacts. This allows the circuit to operate as a general-purpose switch. I`ve used a SPCO/SPDT relay - but you can use a multi-pole relay if.... -
This is a simplified version of the 4-Digit Keypad Controlled Switch. I have modified the design to reduce the complexity of the circuit - and the number of components required. As a result - the code is somewhat less secure. However, there should be lots of.... -
Driving the highway with your high-beam headlights can really increase your visibility, but can he a blinding hazard for other drivers. This simple circuit can be wired into your headlight switch to provide automatic switching between high and low beam.... -
In most countries it is now mandatory or at least recommended to have a rear fog light on a trailer with the additional requirement that, when the trailer is coupled to the car, the rear fog light of the towing car has to be off. The circuit shown here is.... -
This is a single channel (on / off) universal switch that may be used with any Infra Red remote control that uses wavelengths between 850-950nm....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Voltage variations and power cuts adversely affect various equip- ment such as TVs, VCRs, music...
Power is applied to the circuit with the initiate switch open. The 25-JtF capacitor charges...
This hardware-software combination deletes clocks from the slave until both /iPs synchronize....
Note that Tl and T2 are TOKO, including part numbers for the coils Tl and T2. The...
This is one of the most accurate and simplest LC inductance / capacitance Meters that one can...
This is the scheme diagram of 500W power inverter circuit which build using 10 pieces of...
A 6 watt audio amplifier circuit using TDA2613 is shown here. TDA2613 is an integrated Hi-Fi...
This circuit delivers an initial voltage of 2. 5V per cell to rapidly charge a car battery. The...
DC motor driver circuit in the following circuit images can be used for DC motor drivers and can...
Before attempting to build the control circuit, it is recommended that the function of each part...
A very interesting project of a light activated alarm or morning alarm circuit. The circuit will...
We are surrounded by battery operated equipment of all kinds, and this array is growing still....
Here is an infrared remote control tester circuit that can be made without spenting much money....
Before you use LEDs, it`s a good idea to check them out. With a LED tester, you can even do it in...
Low-Pass and High-Pass audio output signal filters. Additional Sound Source Low Pass filter and...
This small FM transmitter with a range of about 50 meters designed for connection to the USB...