Repository-circuits
- Page 603-
It is to be used as amplifier of potency of RF in the high strip of of the power source that should be capable to supply a tension of 13 volts with a current of 10 amperes. it demands right care in the assembly of the source. Terrified armored transformer,.... -
Here is the 22 watt stereo audio power amplifier circuit diagram based on TDA1554 and integrated circuit from NXP semiconductors (formerly PHILIPS semiconductors). It is very simple and useful circuit for amplify the stereo signals. The circuit dissipates.... -
This HD TV UHF wideband amplifier (Ultra High Frequency amplifier ) has a total gain of 10 to 15 dB in the 400 850 MHz domain frequency so it can be used where the tv signal is weak. For this UHF antenna tv amplifier to work correctly you need to cut the.... -
The circuit integrated la3607 allows to just set up a graphic equalizer of 7 bands for a channel adding some capacitors and variable resistors to the circuit. The cut frequency can be adjusted using variable resistors. It possesses high stability for loads.... -
Evolution FM transmitter with 2n2218 with audio amplification step using LM741 op amp with audio input for MP3, MP4, mobile, computer and other audio sources, beyond the traditional electret microphone. With great sensitivity to the input signal. Using fewer.... -
The LM358 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also.... -
That circuit is to test the motor servant of the parabolic antenna it is working perfectly, although a system with lnbf is much more appropriate, a lot of people they still use systems using lnb and servo motor. Then the idea of that circuit is to help to.... -
Converser of temperature tension. To be used with a digital multimeter with reach from -40 °C to 110 °C. With checker of the state of it laughed and a without any adjustment, thanks to LM35! The ice is founded the 0 °C and the point of ebullition of the.... -
This small circuit transmitter processes the signs of audio of a sound table or microphone, and the signs of video of a camera, or still the audio signs and video of a DVD, Video-cassette or even it sweats her video plate has an exit of composed video, you.... -
This small transmitter can arrive the more than 1 km in favorable conditions of emission. The modulation can be made so much with a microphone, for an electrets microphone, or other audio source. The 5 turns of enameled thread 22 AWG, with diameter of 1 cm.... -
Just point this small device at the TV and the remote gets jammed. The circuit is self explanatory. 555 is wired as an astable multivibrator for a frequency of nearly 38 kHz. This is the frequency at which most of the modern TVs receive the IR beam. The.... -
Since then NL has evolved into the Microsoft Windows ®-based NL4, which has been used extensively by world-class engineers in different fields of electronics for almost 10 years. NL5 is the first version to be publicly available. Unlike conventional.... -
The magnetometer was moved to an outdoor location and a specialized enclosure was built. An accessory temperature controller was included to maintain a constant temperature and digital link was created to ferry the recorded data back into the laboratory..... -
The general idea is to space the time internals to increment the DAC output values. There would be 256 levels since there are 8 digital outputs from the Arduino board. Therefore, for an 8-bit, 50s ramp time for example, the way to generate a digital ramp .... -
Inverter circuit to power EL backlights and fluorescent tubes, so the output is about 127 VAC as he claimed. But I want 1kV or more to make at least 1mm purple plasma as Tesla coil usually produce! (30kV is required to make 1cm length plasma). Therefore i.... -
In the voltage to time conversion section, the analog input voltage is fed to the attenuation circuit. The attenuated signal is compared with the the ramp signal generated by the ramp generator given in the block diagram by the input comparator `C1`..... -
The Dynaco Mark III is the highest power amplifier that was widely sold under the dyna name. There was a nigher power amp (the Mark VI), but it wasn`t widely available. The Dyna MKIII has a basic design flaw that none of the other Dynaco products have. The.... -
When a GATE signal (between 3V and 15V), the capacitor C5 acts as a differenciator and converts the gate signal into a brief positive pulse (width 10 ms). D1 protects the circuit from negative voltages. The brief pulse created on the rising edge of the GATE.... -
Trimming is quite easy if you use matched NPNs for Q1 and Q2, and 1% tolerance resistors for R6 to R11. You will need a dual trace scope, a DVM and a sinewave generator. Using 10 turn trimmers is a little bit more expensive than using 1 turn but makes it.... -
I needed an excuse to use the soldering iron so I figured that I might as well as make a frequency counter which is something that I`ve always wanted, but lacked in my lab. Here`s the schematic. I drew it up in OrCAD PSpice a while back. Since then, I have.... -
Controlling the speed of a motor is very important in many situations especially in robotics. There are many techniques of controlling the speed of motors, each with their advantages and disadvantages. This document will show you how to build a motor.... -
For the purpose of this project, digital signals can be communicated with computers while analog signals can`t. RS232 is the name given to your serial port. At the back of your computer, there`s many ports where you can plug things into. The RS232 port has 9.... -
Fly back transformers are commonly found in television sets and can put out 50, 000 volts, enough power to lift a 350 pound man up and throw him back 10-20 feet killing him instantly. Also the component`s are picky sometimes and reversing the polarity....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Two integrated tone decoders, XR-567 units, can be connected (as shown in Fig. 1A) to permit...
When activated, the transmitter sends out a 49.890-MHz, AM rf carrier. The.receiver detects,...
The Radio Hat was a portable radio built into a pith helmet that would bring in stations within a...
The joule thief is an electronic circuit that allows you to make use of batteries normally...
This electronic liquid detector circuit diagram is based on the ULN2429 monolithic bipolar...
This instruction shows how to convert a standard microscope with light bulb to LED light. Only a...
To avoid hum and interference in our high quality DAC we need to galvanically isolate him from a...
This machine uses FD-CAS-923 1 stepper motor control experiment board with 4-phase step motor to...
Common series negative feedback amplifier (2) series negative feedback amplifier shown in series...