FM Radio Circuits
- Page 13-
This fm transmitter circuit is very simple and it has a acceptable transmission. The signal transited from this fm transmitter circuit can be received at almost 300 meters in open air. The circuit require a 3volts operating voltage and can be tuned anywhere.... -
The tuned coil L1, has two output tapping for the antenna connection, marked "A" and "B". These are both low-level outputs and you choose which tapping you want to use ( stable low range, or more unstable but higher range). Tap B (2. 5%) takes just a very.... -
Using BA1404 can be designed a very simple and useful fm stereo modulator electronic project. This BA1404 fm stereo modulator device works in FM broadcast band ( 75- 108MHz) and require few external common components. The BA1404 fm stereo modulator Ic.... -
This stereo FM stereo modulator circuit use the BH1417F FM stereo transmitter IC which consists of a stereo modulator for generating stereo composite signals and a FM transmitter for broadcasting a FM signal on the air. The stereo modulator generates a.... -
This portable am fm radio circuit is designed using the LA1800 IC and some other external components. As you can see in this circuit diagram the LA1800 manufactured by Sanyo Semiconductors, require few additional components. Also the output signal is driven.... -
A very simple FM transmitter circuit can be designed using MC2833 integrated circuit, designed for cordless telephone and FM communication equipment. It includes a microphone amplifier, voltage controlled oscillator and two auxiliary transistors. The final.... -
The TDA7000 has an FLL (Frequency-Locked-Loop) system with an intermediate frequency of 70 kHz and the selectivity is obtained by active RC filters. The only function which needs calibration is the resonant circuit for the oscillator (for the reception.... -
TDA7088 contains a frequency-locked-loop (FLL) system with an Intermediate Frequency (IF) of about 70 kHz. For supplying this circuit we can use an 3 volts battery cell or a regulated power supply. .. -
The pilot detector output is designed as an open collector output, therefore an external pull up resistor is needed. To force the decoder to "MONO" Pin 19 has to be clamped to a voltage below 0. 8V. .. -
The IC is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal PLL demodulator for positive and negative modulation, including sound AM and FM processing. A special function is implemented for the demodulation of FM radio signals.... -
3V FM Transmitter Circuit This project provides the schematic and the parts list needed to construct a 3V FM Transmitter. This FM transmitter is.... -
CXA1019 FM RADIO CXA1019 is a one-chip FM/AM radio IC designed for radio-cassette tape recorders and headphone tape recorders, and CXA1019S has the.... -
This FM booster that can be used to listen to programmes from distant FM stations clearly. The circuit comprises a common-emitter tuned RF preamplifier wired around VHF/UHF transistor 2SC2570. (Only C2570 is annotated on the transistor body. ) Input coil L1.... -
TDA7000 FM Radio Receiver Circuit Using Tuning Capacitor GENERAL DESCRIPTION The TDA7000 is a monolithic integrated circuit for mono FM.... -
This new stereo FM Micromitter is capable of broadcasting good quality signals over a range of about 20 metres. It`s ideal for broadcasting music from a CD player or from any other source so that it can be picked up in another location. For example, if you.... -
I wanted to use a 3. 5" jack instead of a microphone, I would need to change something else in the circuit. What would be changed in order to use an audio jack instead of a electret microphone to transmit One like this: taken from an old radio. It has 7.... -
This amplifier designed for TV transposers and transmitters, it incorporates microstrip technology and discrete linear push-pull transistors with gold metalization and diffused emitter ballast resistors to enhance ruggedness and reliability. Fully assembled.... -
This house FM transmitter for your stereo or any other amplifier provides a good signal strength up to a distance of 500 meters with a power output of about 200 mW. It works off a 9V battery. The audio-frequency modulation stage is built around transistor.... -
This fm 88-108 Mhz radio amplifier is equiped with BLF 245 and can be user with a heatsink from a processor and cooler. The BLF 245 Datasheet can be downlo.... -
This FM broadcast rf amplifier is built with 2SC2539 which is a silicon NPN epitaxal planar type transistor designed for RF power amplifiers in VHF band mo.... -
This 300W RF power amplifier for your fm transmitter has 2 x TP9383 transistors. 300W radio power amplifier for 88 - 108 MHz band. 300W RF power amplifier.... -
The wireless fm transmitter circuit described here has an extra RF power amplifier stage, after the oscillator stage, to raise the power output to 200-250.... -
This low power fm transmitter is designed to use an input from another sound source and transmits on the commercial FM band. This low power fm radio transmitter it is actually quite powerful The first stage is the oscillator, and is tuned with the variable.... -
This fm transmitter is build with UPC1651 which is a silicon monolithic integrated circuit especially designed as a wide band amplifier covering the HF ban.... -
This is a low cost fm antenna booster that can be used to listen to programmes from distant FM stations clearly. The antenna fm booster circuit comprises a.... -
A very good 1 watt fm transmitter circuit, very easy to build circuit. It has 4 transistors, one is a very stable oscillator, followed by a buffer stage to prevent frequency variation when you adjust the transmitter. Next is a resonance stage and the final.... -
The PLL transmitter exciter has the functions of providing a stable, low noise, frequency-selectable RF signal and amplify it to a controllable output power sufficient to drive the power amplifier. It uses a PLL frequency synthesizer built with MC145151,.... -
This is very stable, harmonic free, long range fm transmitter circuit which can be used for fm frequencies between 88 and 108 MHz. This can cover 5km range....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
The LED is the CSL310L which contains a red LED and a green LED connected back to back and...
A simple level of power meter can be arranged to give a bar or dot display for a hi-fi system....
In operation. the alarm circuit allows a 0-47 second time delay, as determined by the Rl/Cl...
When power is applied to the circuit, the heater coil in the sensor is energized by the 5-V...
This system operates on the principle that capacitance loading of an oscillator will lower its...
The ADC Tester (A2100) is a LWDAQ device that records the output and power consumption of two ADC...
Here is a project Device switching using password by innovative group Dreamlover technology,...
By the pLPC1342V and NE (two company names and fever on the tube amplifier circuit 2SA1227A...