FM Radio Circuits
- Page 12
-
Telephone Tone Ringer TA31001 The UTC TA31001 is a bipolar integrated circuit designed for telephone bell replacement. It CAN also be used as alarms or other alerting devices. By LianShun Electronics Co. , Ltd ..
-
-
The TK10931V is an IF IC contains 2 IF systems ( one is for FM, the other is for AM ) and detector. It is suitable for amateur Radios CB Radios scanner receivers, utility Radios and so on. By Toko Inc. ..
-
-
Zilog`s Z8 Encore XP F1680 Series incorporates a best-in-class feature set that is optimized for stepper motor microstepping controls. The features of Z8 Encore! XP F1680 include: A fast 11 MHz internal Oscillator Two Analog Comparators 10-bit....
-
-
L2 RFC (resistance 1MOhm with wrapped around her inductor of enough coils from fine isolated wire. Scratch of utmost inductor and you stick in utmost the resistance making thus a parallel L-r circuit. ) With their C7, C8 we adapt the resistance of aerial....
-
-
This SMD FM transmitter has an operating frequency of about 80 to 115MHz. Under reasonable circumstances you will be able to receive its signal at a distance of about 200 meters. Although it is low-power, it might be illegal in your part of the planet.....
-
FM and AM transmitter in one small device built of cd4001 integrated circuit. It broadcasts on 20MHz(AM) and 100Mhz(FM)....
-
This small transmitter uses a hartley type oscillator. Normally the capacitor in the tank circuit would connect at the base of the transistor, but at VHF the base emitter capacitance of the transistor acts as a short circuit, so in effect, it still is. The....
-
This circuit may be tuned to operate over the range 87-108MHz with a range of 20 or 30 metres. I have used a pair of BC548 transistors in this circuit. Although not strictly RF transistors, they still give good results. I have used an ECM Mic insert from....
-
This is the schematic for an FM transmitter with 3 to 3. 5 W output power that can be used between 90 and 110 MHz. Although the stability isn`t so bad, a PLL can be used on this circuit. This is a circuit that I`ve build a few years ago for a friend, who....
-
-
Small telephone bug. Listen telephone line on your FM receiver. It is self powered. Small part count. Circuit diagram, schematics, electronics project....
-
Crystal X1 is fundamental mode, calibrated for parallel resonance with a 32 pF load. The final output frequency is generated by frequency multiplication within the MC2833 IC. The RF output Buffer (Pin 14) and Q2 Transistor are used as a frequency tripler and....
-
The TDA7010T is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components is important (small dimensions and low costs). The IC has an FLL (Frequency-Locked....
-
The TDA7021T integrated radio Receiver circuit is for portable radios, stereo as well as mono, where a minimum of periphery is important in terms of small dimensions and low cost. It is fully compatib....
-
-
The above circuit is fm receiver. when i used pin supply 9V, this circuit had quite nice performence. But when i used AC/DC rectifier or switch supply ....
-
Hello, I want to build a system that can transmit in the FM band. I have already built my oscillators because I want to transmit at more than one....
-
The circuit was designed to produce a 500mW output power transmitter whose signal modulated by FM using four transistors. Transmitter an electronic devi....
-
The circuit was designed to operate a frequency modulation voice transmitter over the FM band 2 frequency range of VHF. Transmitter an electronic device....
-
This FM transmitter circuit is very simple and it has a acceptable transmission . The signal transited from this FM transmitter circuit can be received at....
-
You ll find that this is a very easy project to build. It will transmit good quality sound in the FM band ( 88 108 mhz ). One inportant item is that the....
-
Here is a very simple, inexpensive and interesting project which provides lot of fun to a home experimenter or hobbyist. This simple transmitter can trans....
-
The range of this FM transmitter is around 100 meters at 9V DC supply. The circuit comprises three stages. The first stage is a microphone preamplifier bu....
-
-
-
-
This the fm wireless transmitter circuit, the truth is one kind microphone that developed to be used without a cable from the microphone to the amplifier. Makes....
-
This circuit is FM radio receiver that very small size and works well, although the sensitivity is poor. The principle of this circuit is to use the generator....
-
A very simple circuit for FM receiver, no IC required, and only a single transistor. I`m not sure whether this transistor works or not, I`m going to try this out. Have you guys seen this before It is a regenerative or super-regenerative simple radio....
-
Colpitts oscillator. Its frequency depends on the capacitance of the vary cap diode. The center frequency is changed by varying the biasing voltage of the vary cap through the 47K pot. You can use a 75cm telescopic antenna or simply a length of hook-up wire.....
-
The RF oscillator using the inverter N2 and 10. 7Mhz ceramic filter is driving the parallel combination of N4 to N6 through N3. Since these inverters are in parallel the output impedance will be low so that it can directly drive an aerial of 1/4th....