RF Receiver Circuits
- Page 5-
The TDA7088T can be used in mono portable and pocket radios. This is a bipolar integrated circuit. Here`s one of the application circuit diagram: When a... -
This is a very simple FM receiver which build based on one transistor only. No chip or another active component. The output is connected to earphones, you need an amplifier circuit if you want to listen the radio with a loudspeaker. .. -
This is a project from the dim and distant past that has proven to be a real winner. I have used it as a basis for an 8 channel proportional R / C (AM) and 145MHz FM chat box. Recipients very simple and is shown below. This consists of a single transistor.... -
GENERAL DESCRIPTION The TDA7000 is a monolithic integrated circuit for mono FM portable radios or receivers where a minimum on peripheral components is important (small dimensions and low costs). The IC has an FLL (Frequency-Locked-Loop) system with an.... -
Here the AM Radio receiver circuit diagram based on old single IC MK484. Components part list: R9, R10_ 6R8 R6_ 100R R3_ 1K R1_ 4K7 R7_ 5K6 R4_ 10K R2_ 100K R5_ 150K R8_ 820K Pot_ 10K log pot Coil & ferrite bar set C7_ 470p ceramic C, C4, C5, C6_ 470nF.... -
This is the simple design and sensitivity and selectivity of the receiver are good. This circuit is use a compact three transistor, regenerative receiver with fixed feedback. The circuit is based on transistor as core of the operation. The transistor that is.... -
40 meter Direct Conversion Receiver. Using the circuit of 40-metre band direct-conversion receiver descr- ibed here, one can listen to amateur radio QSO signals in CW as well as in SSB mode in... -
3GPPFDD_UE_RX is the test bench for 3GPP FDD user equipment receiver testing. The test bench provides a way for users to connect to an RF circuit device under test and determine its performance using pre-defined test bench measurements. This test bench.... -
This page documents an older version of the project that proved very unreliable. This is (still) an ongoing project when I get free time, so I post periodic updates here until I get a proper design/rig and eventually create a new page for it (with pictures.... -
By taking advantage of certain characteristics of superhet action not normally used, it is possible with one pair of coils to cover both the 80- and 40-meter ham bands as well as ranges where commercial point-to-point c. w. and shortwave broadcast signals.... -
Oscillating circuit (coil) are made on a ferrite bar. If you wish to listen long waves winding "1-2" has 135 turns and 3-4 has 20 turns. If you wish to receive medium wave winding "1-2" has 75 turns, and "3-4" has 7 turns (wire used must be CuEm 0. 15mm). In.... -
All coils are designed using an inch diameter pvc pipe using 20 gauge insulated hookup wire, L1 require 6 turns and L2 require 14 turns. You can add turns to or subtract turns from L(or change C2) to receive other frequencies. Q2 and Q3 form an amplifier,.... -
Using TEA5551T monolithic integrated radio circuit can be designed a AM radio receiver circuit which is designed for use as a portable radio receiver with headphones. The TEA5551T radio receiver circuit contains all is needed for a AM radio receiver circuit.... -
Before the advent of broadband communications receivers with synthesized oscillators, high-grade, hamband receivers used crystal oscillators and a variable IF to cover relatively narrow (500-600 kHz) frequency segments. The schematic shows a circuit that.... -
Design A Low-Cost 4- To 20-mA Receiver Circuit For Control Loops | analog-to-digital converter (ADC)... -
This tiny receiver is not much bigger than an AA cell. It is powered off two LR44 button cells, which are expensive and I assume wouldn`t last terribly long. I`ll be on the lookout for LR44`s at the markets and $2 shops now that I`ve got this radio! As with.... -
Communication in F.M. band is easy.circuit diagram with description of Power Full F.M. receiver using single IC receive 88 MHz to 108 MHz frequency in F.M. band,... -
This website was created to help students find idea for their project/FYP. All the content presented here are found from me, reliable blogs, website and forums. The owner of this website takes no responsibility what so ever for any of the content. If you.... -
The old common-base audio preamp, having a noise figure of 5dB is an obvious target to improve the noise figure. A common-emitter configuration, with shunt feedback gives 50 ohms input resistance (preferred by the mixer) and a 2dB noise figure. Two.... -
The antenna coupling capacitor is a critical component in a regenerative receiver without an RF stage, like the Twinplex. In such a receiver, the antenna is an integral part of the regenerative detector, and for proper operation the coupling to the antenna.... -
Covering FM radio reception frequency, by adjusting the L value (La stretch or compression coil L) can easily change the transmission frequency to avoid the FM radio. Transmit signal coupled to the antenna through C4 to launch out... -
In order to understand how the following circuits are connected to each other you have to read the concept chapter first. Of course it is up to you to take just one or two of these circuits for your own developments. Lets start with the 6 MHz oscillator. The.... -
This is probably the simplest radio that one could ever imagine of making. The circuit is so simple that it could be finished assembling within a few minutes and you are already listening your favorite programs over it. The circuit of a single transistor.... -
Have finished documenting/cleaning the code for my Jaycar el-cheapo Thermor/BIOS branded wireless weather station receiver. The basis for the code comes from the Practical Arduino weather station receiver project. In the end all it took was a week of.... -
A very simple direct conversion receiver based on the NE602 Gilbert Cell mixer and a LM386 audio amplifier. The circuit is based onthe famoussudden receiver design from the Rev George Dobbs G3RJV many years ago and looks something like this: My.... -
By combining a current-reuse amplifier and switch based mixer, a dual-band receiver front end offers excellent performance with extremely low power consumption.... -
Ralph Stirling, KC3F, and I built the first generation using a Texas Instruments C5X DSK digital signal processing starter kit. Let it suffice to say that the second generation is a tremendous improvement over the first, because it uses a much more suitable....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
LED 1 will light and the buzzer turns on when the coil is changing inductance. The setup is easy,...
The simple circuit transforms the steady beep of an audible-signal device, such as a Mallory...
Rechargeable lithium-ion (Li-ion) batteries are everywhere these days, powering everything from...
This device ensure a lot of implementation possibilities because it has wide input voltage range...
This simple circuit will energize and de-energize a relay at the push of a button. Any type of...
This project was a sort of challenge: designing an audio amplifier capable of delivering a decent...
As shown in FIG wind speed programmable circuit. The circuit consists of step-down rectifier...
Circuit shown in Figure, LD168 is a flash of tape recorders speaker for sound level indication...