Repository-circuits
- Page 13
-
-
-
The circuit diagram of Radio Collar Transmitter has been described here. This circuit is based on the IC NE 555 which is the central part...
-
Here is the circuit diagram of remote controlled appliance switch circuit. The main parts of this circuit are IC1 (NE 555), IC2 (CD 4017)...
-
The circuit diagram of 7 segment counter circuit has been published here. This circuit consists of counter IC CD 4033 as its central part...
-
The Circuit is the diagram of a simple three band graphic equalizer circuit. An IC called LF 351 IC is used here...
-
The circuit diagram of lead acid battery charger has been described here. The core part of this circuit is the IC LM 317...
-
-
Figure shows the circuit diagram of multi tone alarm. This is basically an amplifier circuit. The central part of this circuit is the dual...
-
Project Manager Jim Heck G3WGM has given an exclusive audio interview to the TX Factor s Bob McCreadie G0FGX which explains what the tests are all about and the potential problems. Membership of AMSAT-UK is open to anyone who has an interest in amateur radio....
-
An internally compensated operational amplifier is described which has been fabricated using n-channel Al-gate MOS technology. Only enhancement mode devices are used, and the circuit has been designed so that its performance is insensitive to process....
-
-
This project provides the schematic and the parts list needed to construct a 3V FM Transmitter. This FM transmitter is about the simplest and most basic transmitter to build and have a useful transmitting range. It is surprisingly powerful despite its small....
-
-
In the Knight Rider circuit, the 555 is wired as an oscillator (Astable mode). The output of the 555 is directly connected to the input of a 4017 decade counter. The input of the 4017 counter is called the CLOCK line. The 10 outputs Q0 to Q9 become active,....
-
-
I`ve made more headway. The other day I built a 6kHz oscillator using a 555 to produce a clock signal that I could inject into the 832. You can see the trace on the scope, and the oscillator itself pictured below. While running on the new clock, the rest of....
-
The Visual Target Tracking System (VTTS) is a system for visually tracking targets using a gimbal mounted camera and digital control circuitry. A small black and white camera is mounted on a stand that can be moved with two directions of freedom. When an....
-
-
A collection of drawings of different 555 applications. Some are drawings of schematics found on the web and in books, and saved for my own reference. I did not save the web pages that these originated from, so some may not have proper attribution. If you....
-
The Hartley oscillator is an LC electronic oscillator that derives its feedback from a tapped coil in parallel with a capacitor (the tank circuit). Although there is no requirement for there to be mutual coupling between the two coil segments, the circuit is....
-
The lighting system of a motor vehicle consists of lighting and signalling devices mounted or integrated to the front, sides, rear, and in some cases the top of the vehicle. The purpose of this system is to provideilluminationfor the driver to operate the....
-
When I purchased this little charger back in 1970 I didn`t think I`d be writing about it today but here we are! Back then I was a lot younger, I had an old car for transportation, and it had an old battery. It didn`t have a lot of cranking power when the....
-
This article is for those who wants to make their own car amplifier. The basics of calculation will be discussed below. If you have understand it you will be able to make car amplifier yourself. Actually the difficulty of designing the car power amplifier....
-
-
The FET amplifier, for those focused on the tube sound, which for various reasons can not be made after the courage to Jiang Sheng-class enthusiasts. bipolar FET tube amplifier and the output characteristics very similar, the frequency characteristics of a....
-
-
P1 is the manual control of the corresponding parameter (e. g. tune for a VCO, frequency for a VCF, manual gain for a VCA, manual phase shift for a phaser and so on). P1 generates the voltage U1. J1 is the (first) input socket for the external control....
-
Input J4 has offset function provided that no plug is inserted into J4 as the switching contact of J4 is connected to the positive supply voltage in this case (via the protection resistor R8). At J5 the inverting sum of all inputs is available. J6 outputs....
-
The subwoofer is a subwoofer or a speaker to reproduce low frequencies, devotee of 20 Hz to 150 Hz electronic circuit diagram below shows the details of a scheme of the main amplifier TDA1516 22 watt in 4 ohm car subwoofer driver. This device is designed for....
-
-
I have been playing with a number of variations of the circuit as a free standing preamp, headphone amp, 321/729 replacements and as a potential active crossover, any and all of which may happen if there is demand. There has been strong interest in all of....
-
-
I have 1968 Ford and the motor identification is now a 1972 engine. Alternator was gone and I have a new one. Was told that I need to reverse the polarity of voltage regulator to make alternator start charging. A diagram of wiring to both voltage regulator....
-
circuit diagram of a modulator circuit in a transmitter and receiver of a amplitude modulation...