Vacuum-Tube Valves Circuits
- Page 2-
Standard linear amplifier according to the standard connection conventional circuit configuration, the power of the beam tube tube according to Figure 1-8, the river. The output stage uses power tubes EL34, KT88. KT100 and other radio beam tetrode,.. -
Transistor radio shows common OTL power amplifier circuit, VT5 bias resistor driver stage. VT6 and VT7 is a pair of complementary symmetry tube. VT6 germanium material NPN transistor, VT7 is germanium PNP transistor. VT6, VT7 and the biasing resistor.. -
6N5P the output impedance of 400 ohms low resistance tube used as a parallel push-pull, the output impedance of a single tube half, and then two-three-plate and pipe used in pa.. -
After the original radio with guts shown transformed into a block diagram of the machine. Electrical schematic shown in Figure 1-27, which is a typical type of tube Group A sin.. -
As a result of high quality materials and advanced technology, the machine output transformer frequency response can reach 10Hz (a 0.8dB) ~ 50Hz (a ldB), to improve the overall.. -
As can be seen from the figure, the self-generated bias amplifier tube for each tube separately to reduce the demanding amateur conditions paired amplifiers camp. Pre-alone DC .. -
As of control type delay circuit discharge Discharge delay circuit and a delay circuit rechargeable compared Discharge delay circuit can obtain a longer delay, and the delay is.. -
As shown in FIG grounds TDA6103Q and color picture tube composed of the actual application. R, G, B input signal from the input socket X3, through the input resistor network co.. -
As shown in a practical single-tube constant current charger, which play a constant role transistor VT1, its current value is determined by the voltage regulator and R2. Genera.. -
As shown in the circuit diagram of the feeding tube Swallow CS37-2 type color TV. Filament voltage by the line flyback transformer, winding current limiting resistor R523 is su.. -
Balanced cross tube inverter circuit is also known Chelles inverter circuit, it can be used as a preamp and 6N10,611 inverted. With the final amplifier tube amplifier using 300.. -
Characteristics of the transistor 811A to the right, when this type of pipe work there is gate current generating means, in order to effectively discharge grid current, convent.. -
Circuit characteristics: O simple phase shift range 180. ; good linearity, control accuracy than the first two, and is suitable for low voltage, but less demanding electroplati.. -
The transmitter was designed with redundancy and cutback (reduced power mode) in mind, giving the transmitter more continuity of service. The final amplifier was divided into 3 separate modules, each using four RCA type UV-898 tubes in push-pull parallel.... -
-
The interest for circuits of tubes, remains big. Thus I will give completed in enough big degree, circuit of preamplifier. It is mainly constituted by the department of main preamplifier, the department of input selector, delay of application voltage and.... -
It is three circuits of RIAA, amplification of low signals of heads [MM], following different solution, each one, as long as it concerns the eq. In the circuit of PHONO 1, we have deephasis with pathetic filter placed between the two departments of tube V1..... -
Amateur Radio Transmitters using valves such as 807 or1625 works well with a plate voltage between 600V to 700 Volts.The circuit described here is a full wave voltage doubler. The output voltage is twice the input voltage. For 230V AC input the output will.... -
The genesis for this hybrid electrostatic headphone amplifier occurred when I was in Hawaii on vacation, at a fancy hotel on Maui. Sitting at the bar on the beach, drinking "Blue Hawaiis," I drew the schematic for the amp on a placemat. The design is my.... -
This is an simple Vox AC amplifier. The circuit is not very clear but is readable... -
-
Figure 1 shows distortion variations in red and violet. Notice how the violet wave follows the green wave perfectly during its positive excursion but falls short of the mark during the negative swing. The red wave is more symmetrical, but does not "clip".... -
This project is finalized, that means it is no longer experimental. This amplifier, altough limited in output power (20W), has been designed to give the best listening pleasure. No compromise has been made during components choice: the 845 output triode is.... -
Pure A class is the most simple topology for designing an amplifier! The tube or the power transistor is loaded directly by the speaker (often thru a transformer, fro impedance matching!), and is biaised at the current necessary for full modulation (that.... -
The circuit is simple, yet is capable of excellent performance. I designed it specifically for use as an amplifier for the digital sound card in my computer. Audio input can be from any two-channel line level device such as a television, CD player, or VCR..... -
The unit is powered directly from the 120 volt AC line, with no power transformers. Filaments are wired in series, with the total adding up to 117 volts (35 + 35 + 35 + 12). The 35W4 forms a half-wave rectifier, which is filtered by a three-stage RC network..... -
With all DHT stages (all tubes from Svetlana 1970-s). OK, the input/splitter are not DHT`s but DHP`s - 4P1L - triode wired. Mullard 3-tube input/splitter topology, cap-coupled to cathode bias 6B4G PP. First stage uses battery bias (no cathode resistor). Only.... -
Here are photos of a tube unit including an analog multiplier, phase discriminator and a relay control driver (a big relay was inserted in a socket near two potentiometers on the left). Used in ground control gear (don`t ask me - control of what..., all I.... -
Vacuum Tubes 807 and 1625 are commonly used by hams as power amplifiers. Both tubes are audio power amplifier beam tetrodes in the output stage of high power amplifiers but they are suitable for high frequencies also. Both tubes are equal in their.... -
For this radio, which I repaired for someone, I made this DIY VL1. Later I found the real tube... -
The Nora K5W is a German radio from about 1929/1930. Is uses the tubes: 2x REN804, 2x REN1004, RE134 or RE604, RGN1054... -
Tube amplifiers designed for headphones have the principal property that they can be used as preamplifiers too. In most cases, the output impedance of a tube headphone amplifier is (or should be) less than the output impedance of a tube preamp. This....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
The circuit shown here is used to switch on a lamp when the tele- phone rings, if the ambient...
One of the difficulties in the design of higher-order tunable bandpass filters is achieving...
Using this(also below in question) circuit to drive a motor, and I heard I should put a...
This is a one chip sound level meter that can be use for displaying sound level of an amplifier...
Today i want to share with you all my water sensor. This is my second successful project when i...
A small Tesla Coil (12" range), Jacobs Ladder or a "Antigravity Project" from the book...
There are battery powered wireless systems on the market, but the ones I found would signal that...
Here is the circuit for the FM Bug. In total there are 18 core components that are needed for the...
The following is a (hopefully clear) description of the final version of the trigger used and a...