FM Radio Circuits
- Page 10-
Input coil L1 consists of four turns of 20SWG enamelled copper wire (slightly space wound) over 5mm diameter former. It is tapped at the first turn from ground lead side. Coil L2 is similar to L1, but has only three turns. Pin configuration of transistor.... -
It is tapped at the first turn from ground lead side. Coil L2 is similar to L1, but has only three turns. Pin configuration of transistor 2SC2570 is shown in the fm antenna booster schematic. Adjust input/output trimmers (VC1/VC2) f.. -
FM transmissions can be received within a range of 40 km. If you are in fringe areas, you may get a very weak signal. FM DXing refers to hearing distant stations (1500 km or more) on the FM band (88-108 MHz). The term DX` is borrowed from amateur radio.... -
Circuit To relieve you of any concern related to high frequency, I used a module ready, in case a module Aurel audio FM transmitter. This tiny circuit board with 2 cm by 4 cm supports a transmitter modulation frequency track, delivering an RF power of 10 mW.... -
I MAID THIS PROJECT SUCCESSFULLY. WITH PROPER FREQUENCY AND STRENGTH. IF YOU WANT HELP THEN CONTACT ME i will surly help you to bring out you from the problem :) .. -
Frequency range is 100-108 MHz. The circuit is only mono circuit, and accepts an audio input from either a microphone or other source. The input impedance is 1Mohm. The input sensitivity is 5mV and the max input signal is 10mV. The transmitted signal can be.... -
It is illegal in most countries to operate radio transmitters without a license so take care with transmitter circuits. This FM low power circuit may be tuned to operate over the range 87-108 MHz band II, with a range of 20 or 30 metres. Active components in.... -
FM Wireless Microphone has been a very popular project with beginners and experienced constructors alike. It has been used inside guitars and as the basis of a remote control system. I do however, receive many requests for a higher powered circuit and better.... -
This Wireless Stereo FM Transmitter built from a monolithic IC. The internal structure of this FM transmitter integrated circuit consist of stereo modulator that creates a stereo composite signal, an FM modulator that modulate a carrier frequency with the.... -
There are currently several nice ICs available that contain a nearly complete receiver. This project is a complete FM receiver circuit with excellent receive and sound qualities. The only disadvantage of using this IC TDA7021T from ST-NXP Wireless, from the.... -
Here`s the circuit diagram of a four RF stage FM transmitter. The stages are, very high frequency (VHF) oscillator built around a HF transistor BF494, a pre- amplifier built around transistor BF200, a driver transistor 2N2219 and a power amplifier using.... -
This is a low cost FM booster circuit to receive far away fm stations clearly on your radio in your local area. The circuit diagram of FM booster consist of a common-emitter tuned RF preamplifier wired around VHF/UHF transistor 2SC2570. The output of the.... -
wireless FM transmitter or often called fm transmitter uses 2 transistors in this article uses 2 transistors 2n2222. If the fm transmitter is in use voltage supply of 9 volt battery and use an.. -
This article gives the FM transmitter circuit schematics with necessary explanation. The main component used here is the VMR6512 IC which is a highly integrated FM audio signal (Hi-Fi Audio FM) transmitter chip. You can use this as FM radio transmitter for.... -
This is a simple 2N2222 transistor based radio FM transmitter circuit within the FCC (Federal Communications Commission) limit, that is no license is necessary for using thisstable FM transmitter circuit. What is an FM transmitter FM stands for Frequency.... -
This is the most simplest and single transistor FM wireless transmitter circuit that ever posted in CircuitsGallery. In telecommunication field, frequency modulation (FM) transmits information by changing the frequency of a carrier wave according to message.... -
With a matching antenna, the FM transmitter circuit shown here can transmit signals up to a range of 2 kilo meters. The transistor Q1 and Q2 forms a classic high sensitive preamplifier stage. The audio signal to be transmitted is coupled to the base of Q1.... -
A very stable and simple FM transmitter circuit is given here. With a matching antenna, this transmitter can attain a range of around 200 meters. I assembled this transmitter few years and got very good results. Let us see how the circuit works. A condenser.... -
With this compact FM adaptor circuit plugged into the audio out of your cassete player or i Pod out put, you can listen your favorite music on your car stereo. This circuit is very useful if your car stereo doesnot have an auxillary in socket. The circuit is.... -
Circuit shown here can be used to jam FM radios in its vicinity. The circuit is nothing but a classic single transistor oscillator operating in the VHF region. Working principle of the circuit is very simple and straight forward. Powerful VHF oscillations.... -
Here is the circuit diagram of an FM remote encoder/decoder using the ICs RF600E and RF600D. These devices are designed to provide a high level of security and operates from anything between 2 to 6. 6V DC. Various electronic circuits like remote control.... -
AN7415 based FM stereo demodulator circuit. 1.6 to 7V operating voltage range. High gain and low distortion.... -
A simple telephone transmitter circuit that is ideal for transmitting the telephone conversation through small distances. The circuit is very simple and uses only few components. The entire circuit can be easily included in the telephone itself or in the.... -
The circuit of a FM Tracking Transmitter Circuit or Remote Control Transmitter Circuit is explained using 555 IC and and 2N4392 transistors.... -
Here is the circuit diagram of an FM transmitter using the IC UPC1651. UPC1651 is a wide band UHF Silicon MMIC amplifier. The IC has a broad frequency response to 1200MHz and power gain up to 19dB. The IC can be operated from 5V DC. The audio signals picked.... -
A simple FM Radio circuit with diagram and schematic using IC TDA 7000. This low cost single chip fm radio circuit design is easy to make and is suitable to make a FM portable radio.... -
A simple Single chip FM transmitter circuit with diagram and schematic using IC MAX 2606, which is a high performance Voltage controlled oscillator or VCO.... -
A simple and high quality FM transmitter circuit designed based on the BA1404 IC .This FM transmitter circuit can be operated from a 3 V battery.... -
This is a simple FM transmitter circuit schematic diagram with a single transistor S9014.... -
This is transmitters circuit that can transmit both FM and AM signal simultaneously at two different frequencies FM in 100Mhz and Am in 20 MHz. Here is the .... -
This Circuit can be used to jam FM radios in its vicinity. This is a classic single transistor oscillator operating in the VHF region. Working principle of the circuit is very simple and straight forward. Powerful VHF oscillations from the circuit will....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
This application involves demodulation of a frequency-modulated subcarrier of the main channel....
This circuit adds 120 degrees of phase shift to a 50- or 60-Hz input, regardless of the...
I have designed this high voltage, low current power supply for various experiments in systems &...
It is very interesting project with many practical applications in security and alarm systems for...
You cannot beat the Chinese. The project described in this article is a ready-made item from a...
Emphasis on the high bands (902 thru 10 GHz) had been a priority here at ARS KMGT for the last...
How does one measure small inductances with a precision of at least two, and possibly three,...
IR remote control for my Nikon DSLR camera. Not that I absolutely need one, surely I don`t need...
One of the outstanding problems in the design of vacuum-tube oscillators is that of keeping the...
Figure 4-11 is a feedback attenuator consisting of transistors tone control circuit. The circuit...