FM Transmitter Circuits
- Page 7-
The circuit is basically a radio frequency (RF) oscillator that operates around 100 MHz. Audio picked up and amplified by the electret microphone is fed into the audio amplifier stage built around the first transistor. Output from the collector is fed into.... -
As shown, the audio ascribe is a microphone, which uses 2 x 2N3904 as the microphone audio preamplifier. The audio/mic ascribe akin is adjustable by agency of a 5k preset / potentiometer. The ambit uses a Colpitts oscillator for abundance generation, which.... -
The transmitter ambit declared actuality has an added RF ability amplifier stage, afterwards the oscillator stage, to accession the ability achievement to 200-250 milliwatts. With a acceptable analogous 50-ohm arena even antenna or multi-element Yagi.... -
The following circuits is one of the power amplifier circuit for FM transmitter with an output power of 30 watts. Power amplifier circuits for 30-watt FM transmitter, the transmitter uses power transistor type 2SC1946A. Power FM transmitter circuits uses a.... -
Place the transmitter about 10 feet from a FM radio. Set the radio to somewhere about 89 - 90 MHz. Walk back tothe FM transmitter and turn it on. Spread the winding of the coil apart by approximately 1mm from each other. No coilwinding should be touching.... -
FM transmitter circuit which is build using single chip of MAX2606. A very simple FM transmitter connects your home-entertainment system to a portable radio that will be carried surrounding the house and into the back yard. As an example, it is possible to.... -
The circuit diagram of stereo PLL FM transmitter based BH1417 chip. This is certainly the most recent BH1417 FM Transmitter design diagram from RHOM that consists of lots of capabilities in a single tiny package. It includes pre-emphasis, limiter to ensure.... -
This circuit connects in series with your home phone line and delivers the phone conversation through the FM band any time you pick up the telephone handset. Transmitted signal could be tuned by any FM receiver. The circuit features an "On Air" LED indicator.... -
These two tank circuits seem to expand that operating spectrum. Maybe The information sheet that came with the bug states that When both circuit stages are oscillating at the same frequency, the power output will be at a maximum. This must mean that if the.... -
FM transmitter circuit very stable and simple given here. With an adaptive antenna, the transmitter can reach a range of about 200 meters. Transmitter met this year and got a few good results. Let`s see how the circuit. A condenser microphone (K1) is used to.... -
FM transmitter or often called fm transmitter uses 2 transistors in this article uses 2 transistors 2n2222. If the fm transmitter is in use voltage supply of 9 volt battery and use an antenna whose length is less than 12 inches, then this fm transmitter will.... -
The important part of the circuit is formed of the Colpitts type oscillator. C3, C4, C5, C6, CD1-CD2 and L1 determines the frequency. BF982 and dual gate MOSFET are active parts in the oscillator. When the input impedance of the MOSFET gate inputs are high,.... -
This is the schematic for an FM transmitter with 3 to 3. 5 W output power that can be used between 90 and 110 MHz. Although the stability isn`t so bad, a PLL can be used on this circuit. This is a circuit that I`ve build a few years ago for a friend, who.... -
This small FM transmitter with a range of about 50 meters designed for hoby. With lots of mini-transmitters then you have a comprehensive, action-packed radio program. Due to the power supply via the USB port of a high frequency stability is achieved..... -
This tutorial is for making simplest FM transmitter using one transistor. You can make this project with less components and it is an easy and simple project for beginners. Before you proceed, please see the schematic given below. In the schematic, you will.... -
This is the schematic for an FM transmitter with 3 to 3.5 W output power that can be used between 90 and 110 MHz. Although the stability isn`t so bad, a PLL can be used on this circuit.... -
This stereo FM wireless microphone also makes a great quality audio link. We tested it to beyond 50 meters and it was rock solid. It s certainly not the first wireless microphone we ve ever published but this one is a little different. It s stereo, providing.... -
A simple whole house FM transmitter circuit diagram and description. Operating power is 1.5V battery of any type. This circuit is able to transmit at a distance of 30 meter. .... -
A good quality FM stereo transmitter circuit schematic using ba1404 fm transmitter IC. Easy to build circuit with only few external parts.... -
This is a long range stable FM transmitter circuit. The circuit is using a LM2950 5V voltage regulator IC comes in TO 92 transistor package, which will provide a stable 5V to the oscillator till the 9V battery runs down to 5. 5 volts, due to which the.... -
Car Mp3 FM transmitter circuit. This circuit can broadcast any audio to FM receiver. It has a good preamplifier circuit so the broadcast sound quality is good.... -
Schematic and description to make fm transmitter. It is a simple fm transmitter circuit with minimum components but it has a long range. .... -
There are many techniques to make an FM transmitter stable so it will not change its frequency as the battery runs down. The rf circuit shown below is a mini stable FM transmitter which is using a zener diode to provide accurate voltage to the oscillator.... -
This 3V FM transmitter Circuit is about the simplest and best basal transmitter to body and accept a advantageous transmitting range. It is decidedly able admitting its baby basic calculation and 3V operating voltage. It will calmly access over three floors.... -
The wireless transmitter ambit congenital about transistor T1 (BF494) is a basal low-power variable-frequency VHF oscillator. A varicap diode ambit is included to change the abundance of the fm transmitter and to accommodate abundance accentuation by audio.... -
I accept acclimated a brace of BC548 transistors in this circuit. Although not carefully RF transistors, they still accord acceptable results. I accept acclimated an ECM Mic admit from Maplin Electronics, adjustment cipher FS43W. It is a two terminal ECM,.... -
The important allotment of the circuit is formed of the Colpitts blazon oscillator. C3, C4, C5, C6, CD1-CD2 and L1 determines the frequency. BF982 and bifold aboideau MOSFET are alive genitalia in oscillator. When the ascribe impedance of the MOSFET aboideau.... -
This ambit is a simple two transistor (2N2222) mini FM transmitter. No authorization is appropriate for this transmitter according to FCC regulations apropos wireless microphones. If powered by a 9 volt array and acclimated with an antenna no best than 12....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Power Saving Using Time Operated Electrical Appliance Controlling System is a reliable circuit...
While discussing an all-linear automatic night light circuit I mentioned that I was testing an...
A prototype model of Agriculture Based Robot . Till recently the farmers were using age-old...
Consider that a school has a total of eight periods with a lunch break after the fourth period....
The EUA2123 is a high efficient Class-D Audio power Amplifier for delivering up to 2G—20W into a...
The circuit timer with musical alarm use famous CMOS oscillator/divider IC (IC1 ). Although this...
The V2. 2 PCB has 4 spare connectors (X11 to X14) these can be used for various inputs and...
The Geiger tube needs a high voltage sup-ply which consists of Q1 and its associated components....
This alarm is designed to sound its Siren only once. That is - when the alarm is activated - the...
Figure 1.88 using the loudness of several tapped the potentiometer control circuit. In FIG. (A),...