FM Transmitter Circuits
- Page 11-
This is the schematic for an FM transmitter with 3 to 3.5 W output power that can be used between 90 and 110 MHz. Although the stability isn`t so bad, a PLL can be used on this circuit.... -
This circuit will transmit a continuous audio tone on the FM broadcast band (88-108 MHz) which could used for remote control or security purposes. Circuit draws about 30 mA from a 6-9 volt battery and can be received to about 100 yards. A 555 timer is used.... -
The range of this FM transmitter is around 100 meters at 9V DC supply. The circuit comprises three stages. The first stage is a microphone preamplifier built around BC548 transistor. The next stage is a VHF oscillator wired around another BC548. (BC series.... -
This opamp is available for only a few pounds. The AD8099 is a very fast opamp (1600 V/ms) and has high-impedance inputs with low input capacitance. The bandwidth of the opamp is so largethat at 100 MHz it still has a gain of nearly 40. This means that this.... -
This is a guide to becoming a techno rebel: a guide to becoming a radio pirate and raiding the silent airwaves with your own content. This is a follow up to my recent call for relaxing the grip on radio broadcasting in the Maldives. One of the easiest.... -
The following plans describe how to build a very small tracking transmitter that can be tracked using an FM broadcast band radio receiver. The transmitter is powered by a 3 volt to 9 volt battery and has a range of from 1/4 mile to over 1 mile depending on.... -
ICs that in the past were far too expensive for the hobbyist tend to be more favourably priced these days. An example of this is the AD8099 from Analog Devices. This opamp is available for only a few pounds. The AD8099 is a very fast opamp (1600 V/ms) and.... -
The range of this FM transmitter is around 100 meters at 9V DC supply. The circuit comprises three stages. The first stage is a microphone preamplifier built around BC548 transistor. The next stage is a VHF oscillator wired around another BC548. (BC series.... -
This is schematic of a synthesized PLL for the Low Power FM transmitter. By the way, you also can use it with other circuits, just pay attention to recalculate the loop filter response and components, VCO tank circuit, and the correct thumbswitch programming.... -
A low power fm pirate radio. The output power is around +35 dBm ( 3. 16 watts) over 50 ohms load and +24 volts power supply. The project consists in a hartley oscillator ( modulated VCO), and tree stages ( Class A, common emitter) of RF amplifiers. The first.... -
Here is the circuit for the FM Bug. In total there are 18 core components that are needed for the fm transmitter to work properly. The far left side has the electret microphone and then things move electrically to the right until they hit the antenna. Don`t.... -
Build this circuit using a Digi-Key Electronics Barrel Crystal (CA-301), 15 Mhz for a standard output frequency of 150. 00 Mhz. If you want to customize the frequency, follow the directions below. I usually build this circuit to operate between 150 to 165.... -
This circuit operate between 150 to 165 Mhz. The Crystals I use Are The Digi-Key Electronics Barrel Crystals CA-301 Type which cost a couple of bucks per crystal. Virtually any Fundamental Crystal between 14 and 17 Mhz will output a frequency of between 140.... -
The DPT Transmitter is a dual powered Voice Transmitter that came about from quite a few request for a transmitter that would function both at power when long range was needed and with a "switch that could be thrown" for a smaller battery consumption when.... -
In the circuit shown, the special launch tube T2 and its peripheral parts form a high-frequency oscillator with frequency in the range of 88 ~ 108MHz. The electret microphone picks up the audio signal, then the signal is amplified by T1, then the amplified.... -
The 2N2222 circuitry is a three-element, phase-shift oscillator circuit, designed to yield a 1,000-Hz sine wave. The 1,000-Hz sine wave is then applied to the TCG-610 varactor diode, 6 pF at 4 V, which changes the tank capacitance, thus varying the rf.... -
Simple FM transmitter with a single transistor. Mini FM transmitters take place as one of the standard circuit types in an amateur electronics fan`s beginning steps. When done right, they provide very clear wireless sound transmission through an ordinary FM.... -
A 27MHz NBFM transmitter circuit schematic with MC2833 and 2 FET transistors MPF6660. Using a Motorola MC2833 one-chip FM transmitter, a few support components and am MPF6660 RF amp, this transmitter delivers up to 3W into a 50 ? antenna. It is capable of.... -
Here`s BH1417 USB FM Transmitter with built-in PLL circuit. Its low-frequency signal is converted into high-frequency, which can take any audio device with FM radio (stereo, car CD, MP3, DVD player, etc.), as a normal radio station. Transmitter power is.... -
The RF oscillator using the inverter N2 and 10.7Mhz ceramic filter is driving the parallel combination of N4 to N6 through N3.Since these inverters are in parallel the output impedance will be low so that it can directly drive an aerial of 1/4th wavelength.....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
These two projects , Wah and Fuzz, are the results of a modification to a Morley dual channel...
The circuit automatically turns on when the car is turned off. It gives you a variable time to...
With the integrated audio TDA8571J designed for automotive applications, this circuit can expand...
This is the circuit of LED color fade effect. Just like the name of the circuit, the light...
This circuit turns-off an amplifier or any other device when a low level audio signal fed to its...
Designing and building a USB sound card longer a head ache got the PCM 2702 integrated circuit...
You need not be disappointed next time when your digital camera shows low battery indication...
There is an advantage in using continuously active PWM signals. The main reason is that the...
Adjusting potentiometer RP, the output voltage of the phase shift bridge diagonal oD phase change...