LED Circuits
- Page 13-
LED guard-rail tube has another name called beautifully the tube, it is a kind of advanced LED decorative illumination lamp decoration products. Use LED of red, green, blue 3 kinds of colors as the light source, has used microelectronics and digital.... -
This circuit in below uses two quad voltage comparator using IC LM339 to illuminate a series of 8 LEDs indicating volume level. Each of the 8 comparators is biased at increasing voltages set by the voltage divider so that the lower right LED comes on first.... -
One of the most popular electronic IC number. There are many different symbols depending on the firm and ability to meet such as 74HC47, 74HCT47, 74LS47, . This is a sign dedicated decoder IC for LED 7-segment common anode. Application when it needs to.... -
LEDs are used more and more in motor vehicles, replacing the standard incandescent lamps because they are more energy efficient and have a much longer life expectancy. In this article we describe a simple LED tail light that has been specifically designed.... -
This circuit is for a simple LED `bar graph` voltmeter. Each op-amp of the 339 quad operational amplifier is used as a comparator for comparing the input voltage Vin against a corresponding voltage level that`s a fixed proportion of the power supply (9V in.... -
This voltage-booster circuit for driving one or more white LEDs uses a 555 timer as its main element ( see the figure ). The timer, IC1, functions as a resettable astable multivibrator where R1, R2, and C2 are the timing components. When the supply voltage,.... -
The circuit shown flashes the LED briefly (to get your attention) and stays on as long as the power is on ( Fig. 1 ). The venerable 555 timer IC can be put to use in this type of application. The circuit is a standard astable multivibrator with resistors RA,....
-
Did it ever occur to you that an array of white LEDs can be used as a small lamp for the living room If not, read on. LED lamps are available ready-made, look exactly the same as standard halogen lamps and can be fitted in a standard 230-V light fitting. We.... -
Here is a circuit for simulating breathing / pulsing LED with the 555 timer chip. It became very popular and i received many comments and emails with people that made this circuit and worked fine, as well as comments with people that had troubles converting.... -
-
Blinks 2 LEDs timely in sequence. Will somebody explain its working I know that capacitor will charge and during the charging the LED will off and whenthey discharge they will on the LED. But why transistor are there.. -
Make those LEDs into LED bar graphs that will show the intensity. For example, I want a song with a loud base to make the bar graph shoot up to the top. The bars of the LED bar graph I would like to just be individual LEDs. I was getting the effect with an.... -
A project called LED Flasher which Flashes LED`s one by one . but I have following Query about my project . if anyone can explain me it in simple words it will be great help for me . one can use Below image for reference or use this link.. -
Designing a controller PCB for a 10x10 white LED matrix clock (inspired by the tutorial here ). It`s based off an ATmega328 AVR IC and Maxim DS3234 SPI RTC. However, I`m stuck: I have no idea how to control my custom non-standard 10x10 LED matrix. Originally.... -
Why have one resistor and transistor for each LED, instead of chaining the LEDs in series and controlling them with a single transistor which is controlled, in turn, by the arduino pin coming in through a single resistor I have no qualms about implementing.... -
Powering the LED with a 3V CR2032 battery and hoping I could extend the battery life by making the LED blink instead of having it on all the time. The 555 timer one, with large value resistors in the voltage divider, is probably the best. It might need an.... -
This is my conceptual schema to use a PIC12 to control the blinking of 3 LEDs with different blinking patterns. I have a few questions that would like to ask... -
It can`t be 0 volts, since the current does not freely move around, due to the resistor; resulting in one side being more negatively charged, and the other more positively charged, since the electrons can move faster to an end of the battery than through the.... -
Control RGB LED strips via a USB or ethernet interface. These strips consume a lot of power and the mass produced controllers suck. I would also like independently controllable "zones" if you will, so ideally this device could power 1 or more strips. Since a.... -
A strip of LEDs from a microcontroller using PWM to control the brightness. The strip I have takes about 1. 5A at 12V. I`m only familiar with purely low power digital electronics so wanted to check if these assumptions are correct and get any advice :-.... -
If you want to build a 7 to 128 demux with 3-to-8 and 4-to-16 demuxes, then put the 3 high bits of your output address into the 3-to-8, and use the outputs of that as the input enable to the individual 4-to-16 demuxes (assuming that it has an enable pin), so.... -
I have a 4 position slide switch according to the position of the slide switch, I should turn on different colored LEDs and also vary the output frequency of 555 timer in astable mode and drive a piezo buzzer. Problem : I cant use the same switch to control.... -
Control a LED with audio signal, but the problem is, that output signal is only 150mVpp (with 150mVpp positive offset). In my understanding, it needs to be higher than 0. 6V to get the transistor running, therefore I am not sure what to use instead. Do I.... -
Performing a chip conversion for the Sparkfun LED RingCoder. The sample code provided with the product works well on an Arduino UNO, but it uses a pin for each I/O - 5 pins for the shift registers and 6 pins for the RGB rotary encoder. What I want to do is.... -
A LED to indicate when a DC voltage reaches 5 volts or more. I don`t want the LED to be dim when it is at 4. 5 or anything. I just want it to be full bright at 5, 0 bright at anything below 5. Is there a way I can do this with discrete components (no IC`s,....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Antennas that are much shorter than 1/4 wavelength present a very small and highly relative...
This is a very simple, low cost, Hi-Fi quality power amplifier. You can build it 5 ways, like...
The control voltage Vc easily sets the cutoff frequency w0 of this state-variable filter to any...
Here is a simple SWR protection circuit you can easily build. The directional coupler and...
given motor coil while motor need controllers to adjust position and speed. Then you will needa...
The large-scale LED display system adopts the line by line scan and lists the driving means to...
Another way other than magnetic reed switches for the alarm trip switch. The circuit needs the...