MCU Circuits
- Page 4-
TCP based security system using the Ethernet module offered within the contest , an ATmega16L microcontroller , a PIR as a sensor and few other peripheral devices , which is specially targeted for homes and small business owners. I have used through for my.... -
I had been putting off writing a driver for some 24LC64 and 24LC256 EEPROMS I was thinking about using, when I came across a temperature logger application written by Seal Ellis. The Temperature logger was posted on on www.avrfreaks.net on January 10, 2002,.... -
The DS protocol was designed to provide firmware-based bidirectional host-to-slave inter processor communications for situations in which no hardware solution is available and the host and/or the slave in incapable of tending the interface in real time. The.... -
This device provides three channels of 8 bit pulse-width modulation. Output pulse duty cycle ranges from 0 to 255/256 in 255 steps. DACs may be loaded by the DS interface. DAC values may also be copied into the on-chip EERPOM and then automatically be loaded.... -
The servo driver is just simply two 4017 decade counters and lots of 0.1" headers. Only populate the A side headers; the B servo bank is optional and will require a few more header pieces. If you received 20 headers, you'll be short two of them. If you.... -
This machine essentially does three things: It controls the process temperature, provides constant agitation of the chemical baths, and performs the timing. The operator must pour in and out the liquids by hand. The heart of the circuit is a Basic Stamp 2p.... -
This is a portable oscilloscope adapter that it can be held in breast pocket. Its operation is only sampling and sending to host PC. The most of functions of the oscilloscope are processed by host PC. Therefore, oscilloscope adapter can be simplified. This.... -
The first SUPERTEF version was using a 68HC11 microprocessor in extended mode i.e. with an external memory program which necessitated many integrated circuits (IC) such as the 74C138, 74C373, 68HC24 and 27C64 making the printed circuit board densely.... -
The diagram of detail of Fig.2 gives additional precise details: The signal HF collected by the antenna is amplified by T1, framed reel S of agreement L1 and L2. To vary the profit of T1, it is enough to vary its supply voltage. Here it passes from 4v to.... -
The quartz QZ1 of the preceding receivers which set the work frequency is not on the market any more. It is replaced by a locking phase loop allowing the free choice of an unspecified frequency on the band used, either the 41, or the 72 MHz. The step.... -
This receptor is born of our annoyance against the irritating problem of Quartz: With the RX21, completed research of cut crystal for your personal rating, you have with him, access to ALL band frequencies, in steps of 5 kHz ! Desiring to make this universal.... -
This receiver weighs about 6 g, used in 41 and 72 MHz, met a great success with readers of the magazine. The RX22 is the subject of these lines is improved RX20. Adding a preamp-HF improving sensitivity. Establishment of an automatic gain control of this.... -
The proposed capacitance is a very powerful assembly to measure in 7 ranges capacitors of 1 pF to 999 uF, avecune excellent precision of about 10 -3 . The range change is fully automatic. The display shows 3 digits with decimal point. Three LEDs.... -
The timer is proposed an effective model for controlling an external load 8A/380V. Equipped with a 68HC11 mu.P associated with an 8 MHz crystal, it can get very precise programmable durations. Two lines are planned: from 0 to 99 seconds and from 0 to 99.... -
Note first the battery to be treated at the center of the figure. It is connected to contacts of a relay. The diagram shows the relay at rest. Under these conditions the battery is in SHOCK . His pole - is grounded and its positive pole to the circuit of.... -
Using the software during flight simulation models of planes: REAL-FLIGHT, we first chose a housing of any transmitter empty direct connection potentiometers innings. However this is not good because, first races of the potentiometers are only 90 degrees,.... -
The UNIVERSAL HOLD circuit detects the dual tone, multi frequency (DTMF) tone that is generated when the # key is pressed and then activates a circuit that partially loads the telephone line so that the central office thinks a phone is still off hook even.... -
M1 is a clamp connected to the 24V (dc or ac) power from the gate opener. The diode bridge rectifies the alternate voltage (should the opener use dc current, it merely adjust the positive and negative rail to match circuit polarity), in order to get the.... -
This design uses a smart card to enable a relay. A Nutchip recognizes its mating smart card among thousand similar ones, because you choose the code to be programmed in the card's memory. No speacilized knowledge is necessary, as we supply the card program.... -
Only one out of 9,999 possible codes has the power to unlock this simple, yet effective, electronic lock. A combination lock is not just a perfect system to protect your belongings, it is also a valid system to let everyone to know that you are vigilant: an.... -
The schematic requires few components, because the timer function has been incorporated by Nutchip. For once, from the start, made up of contacts of the relay RE1 connected to terminal M2. If we turn on an appliance at the end of time, we will use the relay.... -
This project takes advantage from -HOLD input, which is connected to push-button P1. As long as the -HOLD input is low, truth table's timeouts have no effect because this input serves to disable any state change provoked by timers. The effect is to freeze.... -
This design explains how to use an encoder to set the number shown by a 7-segment display. Turn the knob clockwise to increment the number, turn it counterclockwise to set it back. Encoders are the most practical (and handy) way to set a large number of.... -
In this project we'll see how to build a single-channel remote control. It 's a project easy to do : by using a radio module pre-assembled, we will get a card compact without sacrificing performance major. The insert function allows Nutchip impossible to.... -
The remote control transmits encoded signals. Each time a key is pressed, the relevant code is transmitted, usually repeating it many times to ensure reception. This encoded signals travels over a radio or infrared-light beam, to eventually get captured by.... -
We are going to build a START-STOP drive (as commonly found in professional tools), that is a circuit with one switch to run the output (an LED in this case) and one switch to stop it. Nutchip feature two kind of inputs: general purpose and fixed inputs..... -
The schematic is very simple and includes, in addition to Nutchip, with its three driving transistor and LED, the radio receiver. The data come from the OUT pin of the receiver and enter the pin REMOTE remote control. The RESET pin connected to an external.... -
Having to use the infrared remote control, we will procure in addition to modulate the Nutchip infrerossi receiver. Do not let the name fool you, because more than one module component that looks like a large transistor. We use as a reset Nutchip external RC.... -
This circuit is a church bell controller. Basic component is an ATmega32 microcontroller. At the circuit 2 24LC32 eeprom memories is being used, the 1st for internal standard melodies and the 2nd one is for user's compositions. This feature will be provided.... -
As you know the AT90S1200 microcontroller include an internal RC oscillator that is disabled by default. If you want to change it (enable or disable) you must to program it with parallel mode. The most programmers working with serial mode and its not.... -
Your 5x7 display is my favourite toy; the tunes and graphics in the elevator display always impress my mates! Since building the display I developed my own 400 dot matrix using a pic and the SN74154 [4bit binary to 1 of 16 demultiplexer\counter] - in place.... -
A unified thermometric controller that can be programmed with simple scripts, integrating the "classic" thermometer/controller pair. You can build a variety of simple machines with the same hardware and a different script : a charting thermometer, a vending....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Although the 78xx series of voltage regulators are available with different current outputs, you...
The circuit consists of two stages. The first stage is a "switch" or cut-off device. It detects a...
The op amp is connected in the inverting mode. Resistor R3 from the output to the inverting input...
This highly sensitive movement detector is designed from bipolar transistors and draws a curren
If you have ever worked with lasers, you know how fun and interesting it can be, you also know...
After some new experiments on sound analysis, I used a different design for the microphone...
This is another design generated at the request of my father. It is designed to be a dimmer for a...
This humidity detector circuit diagram is very simple and uses few components and can be used for...
This circuit controls resistive and inductive loads up to 2, 500W. Its main functional device is...