The circuit uses two 2N3819 FET`s in cascode configuration. The lower FET operates in common source mode, while the upper FET, operates in common gate, realising full high frequency gain. The bottom FET is tunable allowing a peak for a particular station.....

Preamplifier with LA3161 Preamplifiers are used to amplify low level signals such as those from mikes, tape heads before they are fed into power amplifiers. Power amplifiers ar....

high quality amplifier for headphones electronics project. no need for preamplifier. circuit diagram....

To complement the 60 Watt MosFet Audio Amplifier a High Quality Preamplifier design was necessary. A discrete components topology, using + and - 24V supply rails was chosen, keeping the transistor count to the minimum, but still allowing low noise, very low....

This past summer I saw Transformers: Revenge of the Fallen and I was inspired to build an enclosure for a vacuum tube amplifier that incorporated the Decepticon logo. The tube amplifier replaces a solid-state amplifier which was driven by a tube....

This project uses just one tube. However, the tube chosen (13EM7) actually contains two separate triode structures. One is physically quite small, and is capable of a large signal gain but little power. It therefore makes an ideal preamplifier stage. The....

The ZN459/CP used in this circuit is a high-gain low-noise preamplifier designed for audio/video applications at frequencies up to 15MHz. Figures 2-7B and 2-7C show typical PC board layouts for the ZN459 and ZN459CP (DIP), respectively. Figure 2-7D shows....

This 2 channels audio mixer is based on the 2n3904 transistors which forms 2 preamplifiers. The first preamplifier of the audio mixer has a high gain and can be used for microphone input, and the second one can be used to control the input of the audio....

This circuit is mainly intended to provide common home stereo amplifiers with a microphone input. The battery supply is a good compromise: in this manner the input circuit is free from mains low frequency hum pick-up and connection to the amplifier is more....

Hydrophone preamplifier circuit. As you can see, it`s really simple and uses only conventional components. The transducer used, is piezo type and has a relatively high output impedance, which requires a preamp with a high input impedance. ..

..

This is a simple circuit of magnetic pickup phono preamplifier. A proper loading to a reluctance is provided by this circuit. Here is the circuit: The gain....

..

This Hi Fi stereo preamplifier circuit is built with TDA1054 IC from SGS. TDA1054 is a 16-pin DIL package and integrates 2 separate preamp circuits. It is a low noise preamp with little or no problem in the building process. The first half of the circuit....

..

..

This achievement shows that it is possible to create a balanced dynamic microphone preamp, it is relatively simple. This preamp is particularly suitable for microphones with an output impedance of 200 ohms to 600 ohms. The advantage of the preamplifier. ..

A popular project among microcontroller aficionados is to build a radio-controlled clock. Tiny receiver boards are available, with a pre-adjusted ferrite antenna, that receive and demodulate the DCF77 time signal broadcast from Mainf lingen in Germany. DCF77....

741 Stereo PreAmplifier Circuit Diagram This preamp circuit provides better than 20dB gain in each channel. PARTS LIST R1 -....

..

This circuit is a circuit diagram of ECM Mic Preamplifier. A microphone amplifier that can be used with either Electret Condenser Microphone (ECM). Preamplifier has a dynamic range very well and can handle anything from a whisper to a scream, but must be....

..

The preamplifier offers 20dB in all the region of VHF and it still can reach also their 500MHZ. The amplifier is a circuit of high frequency RF with distinguishable materials. The amplifier as circuit strengthens the tendency of signal with concrete aid,....

Here is a very simple three transistor audio amplifier circuit that can deliver 250mW to a 8Ohm speaker. Complementary transistors BC337 and BC227 (Q3 and Q2) are used as the output pair. Transistor Q1 (BC 547) acts as the preamplifier. POT R5 can be used as....

A Darlington would perform even better, but the circuit would be slightly more complicated. (See the schematic at bottom-right. ) Fortunately, the added complexity is inside the part! The reason for the Darlington`s superiority is that it can provide the....

This microphone preamplifier incorporates automatic gain control, which keeps the output level fairly constant over a wide range of input....

This is a phantom-powered FET preamplifier built into a 1/4" guitar cable, similar to the one on the Tillman site. There are only a couple of parts to the amplifier, so the difficulty was being able to trim and solder component leads to fit within the space....

The SL561 used in this circuit is a high-gain low-noise preamplifier designed for audio/video applications at frequencies up to 6 MHz. Figure 2-6B shows gain versus frequency for various values of C1, and Fig. 2-6C shows gain versus various values of RSET.....

This is a simple microphone preamplifer circuit which you can use betw1een your microphone and stereo amplifier. This circuit amplifier microphone suitable for use with normal home stereo amplifier line/CD/aux/tape inputs. This mic preamp can take both....

A very simple but very good amplifier unit, with low distortion. A similar modification was used as a preamplifier HAFLER. The quality however of the reproduced sound in all the symmetrical amplifiers regardless of the cost of the necessary materials,....

To complement the 60 Watt MosFet Audio Amplifier a High Quality Preamplifier design was necessary. A discrete components topology, using + and - 24V supply rails was chosen, keeping the transistor count to the minimum, but still allowing low noise, very low....

If you`re just building a dual stand-alone preamplifier (as for, say, a stereo magnetic phono preamp), your power supply requirements will of course be greatly reduced. Figure 5A shows a simple supply using readily-available 12 volt, 1/2 ampere transformers....