Top Circuits Page 95
- Page 95
-
A discrete oscillator circuit shown in the schematic diagram below is? a variable duty cycle and variable frequency oscillator, can be used to produce...
-
-
Switch mode/switching voltage regulator with TL497 integrated circuit, up to 75% efficiency, output: 5V, input: 7.5-15V...
-
Using this continuity tester circuit, a failure of? PCB tracks be examined without looking directly at the tracks routing, which is can be very frustrating..
-
A Wien-Bridge oscillator circuit can be built from HA2541 and some basic components. This circuit can generate good-quality sine wave of 40 MHz with an upper limit of 50 MHz. The R3 through R7 and D2 and D1 provide the diode limiting for this circuit. Here....
-
Circuit to control RC servos using 0-10V control voltage..
-
Ensure 5/-5 dual supply for chip TL062 IC3. Gnd is common ps ground, let grounds radiate from ground plane in one side of PCB. R3-R8 is an attenuator that may need to be designed or modified. In output R23 is for protection from shorting of 5V supply, R23....
-
-
Variable power supply for laboratories. With two ICs can take different output voltage and amperage..
-
This is a variable power supply controlled with PIC microcontroller. There is LCD display in this circuit which will show the actual value of power supply output. This power supply use push on switch to adjust the output voltage and current value. The top....
-
This is a LM338 based power supply which is not complicated and easy to build. I am using the supply for a long time, have no problem yet. Only current adjust is missing but I overcome this situation by using an LCD panel ampermeter. There is no PCB for the....
-
LED flasher circuit here will flash a LED using only 1.5 volts ?supply voltage. Normally, to make any LED lamp works, you need more than 2 volts power supply..
-
Speaker relay delay controlling circuit for audio amplidier..
-
-
The circuit was designed to create an electronic oscillator known as Wien Bridge Oscillator which can be used for the creation of low frequency sine wave...
-
This is 10.7-MHz IF amplifier circuit. This circuit is used in many application such as cell phone base station receivers (final IF) and FM broadcast receivers..
-
The ICM7216A or can be used as a minimum component complete Universal Counter. This circuit can use input frequencies up to 10 MHz at INPUT A and 2 MHz at INPUT B. If the signal at INPUT A has a very low duty cycle it may be necessary to use a 74121....
-
This circuit is a circuit diagram mini amplifer. This amplifier circuit has a power of 10 watts. This amplifier circuit is very suitable to apply to your car audio. This amplifier using IC TDA2009A, as amplifeir power. To avoid excessive heat in the IC using....
-
Circuit diagram is a very simple circuit-level indication, with 10 Led. Used a series of half-wave rectification of precision around IC2 TL071, with a single. LM3915 IC is used to control the led, as an indicator VU Meter. LM3915 can be controlled 10 led..
-
Nowadays, it is no longer necessary to use discrete components to build oscillators. Instead, many manufacturers provide ready-made voltage-controlled osci...
-
The 100W audio power amplifier is powered by the integrated circuit LM12CLK which is operational power amplifier..
-
This is a 100MHz Varicap Oscillator circuit. This circuit can provide modulation signals less than 28V and frequency deviation of 28 MHz peak-to-peak. This ...
-
Here the schematic diagram of 100W Inverter Circuit which will convert 12VDC input to be 220VAC output. The circuit built based IC CD4047 to generate sine wave signal 50Hz and then the power transistor 2N3055 will boost the signal so that the signal have....
-
This is a 6m band transmitter RF power amplifier (50 MHz) with 100W output. It used with my FT-736R and drive from 10W for the 6m SSB DX. The Building information comes from Japan CQ Magazine. The Toshiba RF bipolar power transistor is used in it. If you....
-
To lower or raise any specific voltage is better adapted from a transformer, but this component does not operate in direct current, which is available in battery or vehicle. Therefore we must put an oscillator that generates an alternative current. The....
-
This electronic game pits a human player against the ‘machine’. The opponents use a common ‘game token’ and take turns moving along a path by one, two or three steps, and the winner is the first one to reach the goal exactly. Incredibly enough, this simple....
-
The following alarm circuit is designed with features which maybe suited for residential and commercial alarm system applications.this residential alarm circuit also features such delay circuit, 24-hour panic circuit, built-in siren driver, alarm memory,....
-
This is 12V Car Battery Charger simple circuit. This circuit is designed to solve some problems that occurs in most car battery chargers. The problem that occur in most car battery chargers is when the charger is not turned off, the battery will overcharge,....
-
In this article I will offer driver circuit for 12 V/5Watt fluorescent lamp, this circuit used a normal 220 to 10V stepdown transformer in reverse to step 12V...
-
I use a 12V 20W halogen lamp (MR16) and a 4. 2Ah SLA battery for my bike light system. The battery has only limited life at this power rating, so I designed this cheap light dimmer to reduce the battery drain and allow for longer rides at night. Based on a....
-
This circuit is a circuit diagram 12V inverter is very easy to build, cheap components that many electronics hobbyists may even already have. Though it is possible to build a more powerful circuit, the complexity caused by the very heavy currents to be....
-
A 12V portable and mobile power supply circuit design which can be built quite inexpensively and needs only a minimum of circuitry. This circuit will give output current of 1 amp, well stabilized and smoothed..
-
12V power inverter circuit using 555 timer circuit electronic project...
-
This DIY 12V to 220V voltage converter is build with CMOS 4047 that is the main component of this small voltage converter that transforms a12V DC into 220V AC. 4047 is used as a astable mutivibrator, at pins 10 and 11 will have a symmetrical rectangular....
-
The schematic diagram come from circuit: 12V DC Voltage Doubler Circuit power supply. Go to that page to read the explanation about above power supply related circuit diagram. This is the circuit diagram of DC voltage doubler / DC converter. The circuit will....
-
Here the 50W inverter circuit build based power MOSFET FQB45N03 and IC TL494. This inverter will convert 12-14V DC input from car battery, become 220V AC output with 50Hz sine wave frequency. The main oscillator, a voltage reference and comparator collected....
-
We aim to transmit more information by carrying articles. Please send us an E-mail to wanghuali@hqew. net within 15 days if we are involved in the problems of article content, copyright or other problems. We will delete it soon. ..
-
15 Watt switching power supply schematic diagram. Pulse transformer T1 is performed on the ferrite core M2500NMS-2 or M2000NM9 Sh5h5 size (cross-section of the magnetic coils at the location of 5G—5 mm with a gap in the center). Winding wire is made brand....
-
This is the cheapest 150 Watt amplifier circuit you can get, I think. Based on two Darlington power transistors TIP 142 and TIP 147, this circuit can deliver a blasting 150 W Rms to a 4 Ohm speaker. Enough for you to get rocked, then try out this. TIP 147....
-
1500 Watt RF Amplifier circuit can be used to drive your transmitter antenna, it can also include driving to the source of the RF high power, microwave heating, and more...
-
This is a control of servo motors in software programming using PIC 16C71 microcontroller. The input signals are between 0 - 5V delivered by ...
-
Power amplifier circuit diagram using the IC TLE2141C. This is TLE2141C IC IC type Low noise, high voltage, high-slew-rate op-amps. Frequency response 30Hz...
-
18W Audio Amplifier made of transistors..
-
The following document contains information related to Volvo 440 electrical installation schematic diagram. It such the wiring schematic for Volvo 440, 460, and 480 series..
-
This is a standard digital clock circuit,frequency size 1 Hz or 2 Hz. It can be used in the normal clock circuit. It consists of IC-4060 and IC-4013, the...
-
The circuit was designed to create a low cost frequency meter that will cover the range of 1 Hz to 1 MHz with a digital indication using three 7-segment d...
-
This is anaudioamplifier circuit which use TDA7052 as the main component and other 5 pieces of components to support the main component. The ideal supply voltage of this circuit is about 6-12V and no heatsink required. ..
-
1W stereo headphone amplifier circuit, built based TDA2822, designed portable players, radios and other electronic devices which can use headphone as the output...
-
This is an oscillator circuit that can be used for calibrating frequency counters, amateur receivers and frequency meters. This circuit is called 2MHz standard with dividers circuit. This circuit uses two crystals, 100kHz and 2 MHz. Here is the schematic....
-
Field strength meter is a must have equipment if you`re dealing with radio transmitter electronics. Here is one example of this kind of circuit that works for...
-
This is a Mini MW (Medium Wave) Transmitter circuit. This circuit consist of combination of transistors SA103 and SA101. Those transistors is used as oscillator...
-
KA2211 is a dual audio power amplifier for consumer application. It is designed for high power, low dissipation dan low noise. Is also contains various of protectors and suitable for car audio power amplifier with high performance. ..
-
20W TDA2005 stereo amplifier for all suitable applications like amplifying medium power speakers. It is suitable for car use but before, the power supply must be choked with at least 150mH and it must give up to approximately 6 to 7 amps during the upstream....
-
The main features of this powerful MULTIWATT Package (a trademark of SGS-THOMSON Microelectronics), a power amplifier IC chips designed specifically for car radio application, are the high current capability (3. 5A) and the capability to drive a very low....
-
Astable multivibrator or oscillator circuit is based on positive feedback. We can design such circuit using op-amp, logic gates, or transistors. Here we can...
-
It can give ample light even for reading purpose. Capacitor CX along with diodes D1 through D4 forms the AC step down circuit. CX reduces high voltage AC from mains to a low voltage AC which is rectified by the diodes D1-D4. Capacitor C1 removes ripples from....
-
This is a 220V LED flasher circuit which is intended as a reliable replacement to thermally-activated switches used for Christmas tree lamp-flashing. This a cheap circuit and easy to build. R1_ 100K R2, R5_ 1K R3, R6_ 470R R4_ 12K C1_ 1000 F 25V D1-D4_....
-
This is a simple 220V power interface circuit. This circuit used as interface for monitoring electric devices and equipments using a computer. The circuit only...
-
Here is countdowntimer24 second circuit. Thistimercircuit build for automatis on or off electronic load. Thetimercircuits uses fast 74LS schottky IC`s. A 24 second countdown starts when S3 is off and S2 is pressed. Switch S3 is used to start/pause the....
-
Here is the circuit diagram of a simple 24W mono amplifier using IC TDA1516. The TDA1516 is an integrated class B power amplifier in a 13 pin SIL package. The IC has many useful features such as short circuit protection, load dump protection, thermal....
-
This is a programmable clock timer circuit that uses individual LEDs to indicate hours and minutes. 12 LEDs can be arranged in a circle to represent the 12 hours of a clock face and an additional 12 LEDs can be arranged in an outer circle to indicate 5....
-
This is a simple Electronic thermometer circuit. This is a inexpensive circuit because probe or sensor that is used in this circuit is 2N2222 silicon ...
-
Below is two single ended circuits which connected back to back give differential input. This circuit is not only has differential input feature, but also high impedance, much higher compared with the analog ammeter without this circuit. Here is the....
-
This project uses a microcontroller programmed with software that is posted on the Gerns-back BBS at 516-293-2283 as part of RUNABOUT. ZIP. The robot can be controlled via a universal remote control. ..
-
2x22 W car audio amplifier circuit uses TDA1558, a monolithic integrated class-B Output power amplifier contains 4x11W single-ended or 2 x 22 W BTL amplifiers..
-
This power supply is meant as an auxiliary or as a permanent power supply for all common circuits based on a stabilized DC voltage between 3 and 30V provided that the consumption does not exceed 3A. Of course this power supply unit can also be used for other....
-
The following figure shown an example of a three-output flyback regulator built using LM2577 that has electrical isolation between the input and output voltages. The values shown in the circuit diagram will be 5V for the voltage. An electrical isolation is....
-
3.3V and 5V DC DC converter circuit design electronic project using LT3692 DC converter dual tracking regulator..
-
Here is 3 band equalizer circuit other. A tone control circuit made with a single op-amp and having three ranges, bass, middle and treble controls. Using a...
-
Controlling the speed of three phase ac motor is done by controlling the frequency of the power line supply,? since the motor is synchronized with the line...
-
3 to 12 volts step up DC converter using MAX668 integrated circuit design..
-
This project was a sort of challenge: designing an audio amplifier capable of delivering a decent output power with a minimum parts count, without sacrificing quality. The Power Amplifier section employs only three transistors and a handful of resistors and....
-
We aim to transmit more information by carrying articles. Please send us an E-mail to wanghuali@hqew. net within 15 days if we are involved in the problems of article content, copyright or other problems. We will delete it soon. ..
-
This is the schematic diagram of 300W power inverter circuit. The inverter uses power transistor MJ15003 for final amplification. You may replace the MJ15003 with 2N3773 if you have difficulty to find MJ15003 transistor. The inverter will convert 24VDC to....
-
This circuit bellow shows a teleremote circuit which enables switching ?on? and ?off? of appliances through telephone lines. Can be used ...
-
Here`s a circuit diagram for setting the brightness of the light bulb. You simply use the second battery to make the fruits of this circuit works. Example usage of this circuit is to adjust the brightness of images for close-up photo shoot with a digital....
-
To reach low channel ON resistance (<30 Ohm) and low OFF current leakage, 4-channel commutator uses the 2N4091. The DM7800 voltage translator is a monolithic device. This device give us 10V to -20V gate drive to the JFETs while at the same time giving....
-
This is one of the simplest circuit for a PC parallel port based DLA. The Circuit is mainly used to protect the port which is fabricated on the motherboard itself..
-
4 Channel Infrared (IR) Remote is a simple kit using the famous HT12A and HT12D encoder / decoder chips from Holtek...
-
The 555 circuit below is a flashing bicycle light powered with four C,D or AA cells (6 volts). Two sets of 20 LEDs will alternately flash at approximately 4.7 cycles per second using RC values shown (4.7K for R1, 150K for R2 and a 1uF capacitor). Time....
-
This 40KHz crystal controlled oscillator circuit drives an infrared LED with powerful 40ma pulses..
-
This circuit was originally designed to detect weak flashed of laser light bounced off of a fabric video projection screen. It was used as part of a firearm training system. It generates a 100mS output pulse whenever it detects a 3ms to 5ms-laser burst,....
-
This 40V dual power supply circuit was designed in response to a request made by Michael from Philippines. His application is to power the 150 Watt amplifier circuit published here. I think this power supply design is adequate for the purpose. The....
-
This power factor controller accept voltage from 90 to 268 Vac, that`s why we call it power factor controller with universal input, since any standards of mains supply in almost any country would fall within that range. This power factor controller is....
-
The circuit was designed to work with an audio power amplifier which operated off 18v-0v-18v power rails. The actual voltage used is not too critical except that the feedback is referred to the LED chain which itself is anchored to a 12v rail, hence the....
-
We aim to transmit more information by carrying articles. Please send us an E-mail to wanghuali@hqew. net within 15 days if we are involved in the problems of article content, copyright or other problems. We will delete it soon. ..
-
This is the scheme diagram of 500W power inverter circuit which build using 10 pieces of well-known NPN power transistor 2N3055 to amplify the AC signal produced by multivibrator. The frequency generator / multivibrator is built based on transistors too. All....
-
We aim to transmit more information by carrying articles. Please send us an E-mail to wanghuali@hqew. net within 15 days if we are involved in the problems of article content, copyright or other problems. We will delete it soon. ..
-
This is a simple circuit of beeper using 555 timer. This circuit can be employed to energize lights, horn, or other signaling device at any desired interval...
-
The Vc1 increases linearly when the pull-up resistor RA in the monostable circuit is replaced with constant current source, generating a linear ramp. The linear ramp generating circuit and the generated linear ramp waveforms illustration is shown in figures....
-
A square wave oscillator using 555 IC can be configured to give symmetric oscillation (50% duty cycle). Other circuit uses diodes to split the charging and the...
-
To provide rapid motor speed changes and motor direction reversal, four outputs drive a MOSFET H-bridge. N-channel devices are the lower rail power MOSFETs and P-channels are the upper MOSFETs. All of them are driven by the TC4469. A small series resistor....
-
Normally 555 timer circuit even though the start push-button PB1 is not pressed, the timer keeps consuming power From the battery due to a potential divider formed by three 5k © resistors within the IC. this power consumption known as the idling power....
-
The 555 Stepper Pulse Generator kit will help you with the pulse required to drive your favorite DC Servo Motor application..
-
This voltage to frequency converter (VFC) circuit uses 555 IC and 741 op-amp as the main components. Up to 20kHz oscillation can be produced by this circuit..
-
Unique applications of 567 tone/frequency decoder IC? Here is one of them: pulse generator with 25% duty cycle (active factor). This signal generator produce ...
-
The schematic herein appears a 5A H-Bridge Module for the working of one Bipolar DC motor. H-Bridge Module consists of one set header (J2) and one set connector terminal (J1). And here are the J2 pinout description of H-Bridge module interface:...
-
The schematic diagram below circuits 5V/1A Step-Down Switching Regulator using LM2524D Regulating Pulse Width Modulator (PWM). You may see the parameters, PC board layout, stuffing diagram and more in the LM2524D datasheet..
-
This voltage regulator circuit gives a stable 5V output from unregulated inputs (more than 5V). The stability of the output voltage is good enough, only change...
-
This 5 volts Switch Mode Power Supply circuit use the IC from National Semiconductor has been producing and designing ICs for use in switch-mode power supp...
-
The circuit was designed to experiment with using small fluorescent lamps as a broad pattern source of modulated light. The circuit hits the small lamp with narrow 1us pulses at a rate of 10KHz. Each pulse launches about 10 watts of visible light. The lamp....
-
We can say in simple words that AFC will lock the receiver to any valid RF signal. Below, we can see a basic block diagram of an receiver. The VCO is mixed with...
-
This months project is based on the 4017 chip that we used in a project last month. If you haven`t had a chance to review the basics of the 4017 chip you may want to review the info presented in June`s project of the month. As you can see see we have changed....