The circuit given here can be used for tossing head or tail. There are many games in which a tossing is required to start and this circuit can be used in all such instances. The circuit uses two ICs NE 555 timer (IC1) and 74LS76 dual JK flip flop (IC2). The....

The following schematic diagram shows the 12 Volt Car Lamp Dimmer Circuit Design using 555 Timer. This circuit design can be used to dim a standard 25 watt....

The objective of the circuit is to build an electronic dice based on the functions of a 555 timer integrated circuit that operates in the astable mode. LM....

This smoke detector is designed using 555 timer circuit and some common electronic components. The photo interrupter module is used as the smoke detector, while timer 555 is wired in astable configuration as an AF oscillator for sounding alarm via a....

This counter uses a four-digit display, but with a flip of the range switch, it can display frequencies from 1 to 40 MHz, with a resolution of 100Hz. The MM74C926 CMOS IC contains a four-digit decimal counter that can latch a given count and then use this....

This is a motor speed control circuit that allows safe and easy control of 115VAC "universal motors" like drill motors, blender motors, other power tools, etc. The motor is controlled directly by a triac-diac component that is found in variable-speed....

It`s enough to explore PWM and digital-to-analog conversion, and it illustrates how you can create your very own electronics workbench to explore RC filters , charge curves, discharge curves, pulse generators, timers, and even create a very simple....

This circuit turns-off an amplifier or any other device when a low level audio signal fed to its input is absent for 15 minutes at least. Pushing P1 the device is switched-on feeding any appliance connected to SK1. Input audio signal is boosted and squared....

I am attempting to design an alarm using a LM555 timer. I dont know where to start. My friends around have been designing them and I am trying to make ....

This is a starting method that reduces the starting current and starting torque. The device normally consists of three contactors, an overload relay and a timer for setting the time in the star-position (starting position). The motor must be delta connected....

This simple alarm timer circuit is made with 4060 which has an integrated oscillator with a good stability with a relatively wide frequency range. In the c....

This circuit was developed since a number of visitors of this website requested a timer capable of emitting a beep after one, two, three minutes and so on, for jogging purposes. As shown in the circuit diagram, SW1 is a 1 pole 9 ways Rotary Switch. Setting....

This circuit diagram is a UM66 based touch sensitive musical bell. The circuit is built around CMOS IC CD4011 and popular melody generator IC UM66. The circuit contains a pair of touch plates. When these are bridged by hand for a moment, the um66 starts....

The following circuit shows the Bedside Lamp Timer Circuit With CD4060 IC. 30 minutes operation, Blinking LED signals 6 last minutes before ....

This is a programmable clock timer circuit that uses individual LEDs to indicate hours and minutes. 12 LEDs can be arranged in a circle to represent the 12 hours of a clock face and an additional 12 LEDs can be arranged in an outer circle to indicate 5....

A simple light to frequency converter circuit with diagram and schematic.Used as Light intensity measurement circuit.Design using TLC555, a cmos version of NE 555 timer IC....

Manufacturers of cordless drills generally recommend a battery charging time of three hours. Once the charging time is up the battery must be disconnected from the charger: if you forget to do this there is a danger of overcharging the battery. This circuit,....

In this circuit a LM339 quad voltage comparator is used to generate a time delay and control a high current output at low voltage. Approximatey 5 amps of current can be obtained using a couple fresh alkaline D batteries. Three of the comparators are wired in....

This LED Flasher circuit is based on the 555 timer IC. The LED Flasher circuit diagram is very simple and require few external components. When the circuit is working the red LEDs will flash at a set frequency one by one like at the railway crossing indicator...

To build a GaAs FET preamp that has good gain and extremely low noise from readily available components. This preamp is stable with differing source and load situations. The circuit is built dead bug style on a piece of printed circuit board for a good....

The chart shows a function generator circuit composed of 555 timer. The circuit consists of a CH7555 timer and some transistors and RC components. It can generate triangle wave, square wave, sine wave, sawtooth and square wave sweep simultaneously. Ramp can....

I have an Xbox 360 console which used to have a problem with the 3RLOD, I decided to remove the stock heatsinks and install a Koolance external water cooling system. This has remedied the fault with the console superbly (the console now operates at a max.....

This sketch sends an ASCII A (byte of value 65) on startup and repeats that until it gets a serial response from the computer. Then it sends three sensor values as single bytes, and waits for another response from the computer. You can use the Arduino serial....

Add a cheap stopwatch to this circuit to produce an accurate reaction timer. The circuit is wired in parallel with the start/stop button in the watch via a 2. 5mm socket, which fits snugly in one corner of the casing. The person conducting the test (the....

It is not the purpose of this folio to accommodate a abundant account of the IC`s acclimated by this circuit. If you appetite added advice on this accountable amuse accredit to the Flip-Flop Made With A LM556 Timer Chip folio in the assorted circuits area of....

This circuit controls a Searchlight type signal head and produces solid - RED, YELLOW or GREEN indications. The signals can be connected for NORMAL or APPROACH type lighting of the Green signal. The circuit uses a LM556 - Dual Timer IC in a complimentary....

This timer was designed for people wanting to get tanned but at the same time wishing to avoid an excessive exposure to sunlight. A Rotary Switch sets the timer according to six classified Photo-types (see table). A Photo resistor extends the preset time....

This simple alarm circuit was designed for use in a combined garage and rumpus room. It can be assembled on Veroboard and uses just one IC plus a handful of cheap components. The circuit is based on a straightforward 555 timer circuit (IC1). This is wired as....

This circuit has an adjustable output timer that will re-trigger at regular intervals. The output period can be anything from a fraction of a second to half-an-hour or more - and it can be made to recur at regular intervals of anything from seconds to days....

Single Transistor Timer Circuit tutorial for beginners in electronics. Easy beginner electronic circuit that can be built on breadboard....

This is a one module of diesel and horn train circuit. This circuit is work with built by 555 timers IC, and some op amp. This circuit is a complete system for the horn circuit. This is the figure of the circuit. The main power supply to the system must be a....

Digital scoreboard circuit functions to display values from 0 to 9 on the 7 segment display. 7 segments using a type of common anode. 7 segment driver IC using a 74LS47 or 74LS247. On the digital scoreboard circuitry uses a 555 timer ic, serves to produce a....