An ultra low noise audio preamplifier particularly suited to microphone preamplification including balanced microphones. The IC features wide bandwidth, low distortion only 0.007% at a gain of 100, ..

The optical signal is coupled to the pin diode. Current flowing in the diode also flows into the input of the NE5211 preamplifier. The preamplifier is a fixed-gain block that has a 28-K!J differential transimpedance and does a single-ended to differential....

This light-wave receiver consists of a 741 operated as a preamplifier and an LM386 operated as a power amplifier. Potentiometer R2 is the gain control. Various kinds of detectors can be used as the front end of the receiver. Phototransistors are very....

The persona] message recorder is built around an ISD1016 CMOS voicc messaging system, which does away with the cumbersome and expensive analog-to-digital and digital-to-analog conversion circuits. A functional block diagram of the ISD1016 is shown. The....

The gain of the low-cost IC is internally fixed so that it is not less than 34 dB (50 times). A unique input stage allows input signals to be referenced to ground. The output is automatically self centering to one half the supply voltage. The output is also....

A low-noise LT1115 (Linear Technology, Inc.) op amp is coupled to a class-A buffer amplifier to produce a variable g..

The low-cost Mini-Circuits MAR-X series of chips offer the RF builder a real advantage, with their inherent 50- input and output impedances (needed for RF systems). An MAR-1-based receiver/scanner preamplifier is shown. Ci and C2 are chip capacitors. Use....

This circuit is built around two chips: the MC1458 dual op amp, configured as a preamplifier, and the LM378 dual4-watt amplifier. The gain of the preamp is given by R3/R1 for one side and R4/R2 for the other side, which is about 100. That gain can be....

This amplifier is intended to be added to preamplifiers that have no phono input. Such a phono i..

Not much can be said about how the LM382 works as most of the circuitry is contained within the IC. Most of the frequency-determining components are on the chip—only the capacitors are mounted externally..

The circuit of preamplifier use the 5533 chip and features a combination of controls balance and volume. Due to the nonlinearity of the human auditory system, low frequencies must be boosted at low listening levels. ..

This antenna might help to reduce power-line noise. A plastic hula hoop or conduit 3 feet in diameter, covered with aluminum foil as a shield is used for LI and L2. LI is two turns and L2 is one turn, threaded through the loop. SI selects 160- or 80-m....

A high performance op-amp that sets a new standard of excellence in noise performance only 0.9nV/Hz with low source resistances. Total harmonic distortion is less than 0.01%. The op-amp is suitable for use in high quality audio, low noise frequency....

Thiscircuit matches the very high impedance of ceramic cartridges, unity gain, and low impedance output. By "loading" the cartridge with a 2M2 input resistance, the cartridge characteristics are such as to quite closely compensate for the RIAA recording curve...

The indicator is intended for use with an audio amplifier or preamplifier, but it can also be used in othe..

This preamplifier has a built-in regeneration control boost gain selectivity. CI is a single or multi-gang AM broadcast-band tuning capacitor. LI is a ferrite loop antenna, tapped at about 15 to 25% of total turns. This circuit should prove useful for....

The circuit will provide a 20 ±0.1 dB voltage gain from 500 kHz to 50 MHz. The low-frequency response of the amplifier can be extended by increasing the value of the 0.05-JLF capacitor connected in series with the input terminal. This circuit will yield....

This preamplifier provides proper loading ratio of better than - 70 dB (referenced to 10 to a reluctance phono cartridge. It provides mV input at 1 kHz) and has a dynamic range of approximately 35 dB of gain at 1 kHz (2 mV 84 dB (referenced to 1 kHz). The....

This circuit provides about 20 dB voltage gain with a frequency range from 0.5 to 50 MHz. You can extend tbe low-frequency response of this circuit by increasing tbe value of the 0.05-ILF capacitor- or try removing tbe capacitor. This circuit delivers a....

Cl, C2, and C3 are miniature ceramic or plastic trimmers- Tl (main winding) is 0.34 µ,. Use of 11 turns of no. 24 enameled wire on a T37-10 toroid core. The antenna winding has one turn, and Ql the source winding has three turns. T2 primary consists of 11....

An alternate LED driver which uses the 74F3040 line driver was incorporated in this particular application example. The 74F3040.has a higher current rating, but not the variable threshold capabilities at the NE522. The LED diode is operated in the....

The electronic circuit in the VOX Box consists of three parts: a microphone preamplifier, a Schmitt trigger, and a relay driver. Input signals (MIC INPUT terminals) to the microphone preamplifier (Ul) are amplified and fed to a THRESHOLD control (R8). When....

Choosing de rather than ac coupling can reduce much of the noise associated with preamplifiers for a magnetic reading head, particularly in the low frequencies. The LM1897 eliminates the need for the capacitor that usually ac couples the read head to the....

This amplifier is useful for audio and video applications. Gain is set by Rf and the voltage gain of this amplifier ..

The circuit is based on the known chip TDA1524, which is an integrated control Volume, Bass, treble, and Balance. These arrangements are made through 4 potentiometers (P5-P8) with trend. The integrated circuit IC1, to run the needed very few external....

By using the preamplifier with a short length of shielded cable and clip leads, signals that generally could not generate a readout, generate precise and stable readouts on the counter. The DPDT switch is used to bypass the circuit when amplification is....

The gain of the low-cost IC is internally fixed so that it is not less than 34 dB (50 times). A unique input stage allows input signals to be referenced to ground. The output is automatically self centering to one half the supply voltage. The output is also....

The circuit is a form of the so-called ""Americanized" version of the Baxandall negative-feedback tone control. At very low frequencies, the reactance of the capacitor is large enough that they might be considered open circuits, and the gain is controlled....

The preamplifier is protected from excessive input signals of either polarity by the 2N5909 junction field-effect transistor. A nulling circuit makes it possible to set the preamplifier output voltage to zero at a fixed low level (up to + 10~8A) of the input....

That circuit uses the MSM6322GSK which is only available in small 24 pin plastic SOP style package. A speech pitch converter IC that operates in real time and requires very few external components. It has a microphone preamplifier and line level input and....

As shown, the use of the operational amplifier A for audio preamplifier circuit. The advantage is small size, low noise, low power consumption, good consistency. A operational ..

Audio AGC can keep track, monitor audio preamplifier output signal level when the input signal increases, AGC circuit automatically reduces the gain of the amplifier; when the ..