- Home /
- Search about pulse
Page 40 about pulse | |
Total Found: 1277 |
-
Figure 2 is a diagram of the control circuit built on a 1.45 X 1.8 inch PC board. IC1 is an LMC555 CMOS timer that generates a 200 microsecond wide clock pulses to step the motor and control its speed. The speed can be varied by changing the pulse....
-
Commercially available IR distance rangers typically handle a 3- to 30-in. detection distance. Many times, it is necessary to determine smaller distances. The circuit in Figure 1 is useful for measuring small distances to reflective surfaces. Its measurement....
-
This circuit uses a couple of Op-amps to produce an interesting sound effect. The left hand CA741 is wired as a standard astable and produces the timing pulses, controlled by C1, R2 and VR1. The output is fed via C2 to the second op-amp and is also direct....
-
Many electronic-control systems have digital outputs that use transistors. One method of improving the security in these outputs is to use an oscillating signal to represent a logic-high state instead of a fixed voltage level (Figure 1). This type of signal,....
-
The circuit that has been used is shown in picture 1. Through the experimental part we will explain each of the parts function, but in order to have a notion of the basic idea, let just say, that this circuit besides the 5V power supply, is fed with a pulse....
-
Today`s digital delay lines can process pulses no shorter than their delay times, and that restriction confines the devices to applications in which the duty cycle remains near 50%. A limited range of available delays (2 to 100 nsec per tap) further limits....
-
Sometimes when experimenting with different soundcards and MIDI interfaces it is useful to see if there is some data going in MIDI interface. This can be easily tested with this adapter, which converts the midi signals to visible light pulses. Just the....
-
This unit provide 2 way IR communications using a numeric keypad and an LCD display. Data is sent and recieved in ASCII with no regard to what the data means to any particular device. The ASCII data still needs some form of encoding. For this I chose....
-
Analyze your circuits before you build them! PC-ECAP has been one of the world`s best linear circuit analysis programs. The software will calculate and plot: gain, phase, group delay, impedance, VSWR and return loss. This versatile program can also....
-
A battery-powered, pushbutton-triggered TTL/CMOS-compatible source of debounced 5V logic pulses is a simple but handy piece of test equipment to have in any tool kit (Figure 1). The circuit`s battery-powered operation complicates what would otherwise be a....
-
The circuit uses (RGB) Red, Green and Blue high brightness LEDs that are pulse width modulated (PWM) to vary the intensity of each colour LED. This allows effectively any colour to be generated with rapid changing strobe effects, fast and slow colour fades....
-
By using the same circuit of the Digital Stopwatch 0-99sec , we can add an AND gate, and transform the 0 ? 99sec stopwatch to a 0 ? 60sec stopwatch. We must find a way to control the RESET function of the BCD counter, which is responsible for the counting of....
-
The LTC1980 manages both battery charging and generaton of the regulated system bus voltage via a unique bidirectional pulse-width modulator design (Figure 3). When the wall adapter is present, power passes directly to the system load DC/DC converters....
-
This Is a capacitor power supply. This is a very small currents of energy-effective, because it has very little loss, much smaller than the miniature transformer. Capacitor impedance is inversely proportional to frequency. This is a great disadvantage when....
-
In video systems it is frequently necessary to remove the sync pulse from a video signal, while passing the active video information. A familiar application for this is the scrambling of premium channels by cable operators so that they may only be viewed....
-
Figure 1 shows a complete circuit for an emergency lamp that operates from a 12V automotive battery. The xenon flash tube requires a 250V-dc anode voltage and a 4-kV trigger pulse. To generate the 250V dc, IC1, a switching regulator controller, and T1, a....
-
This simple circuit generates narrow pulses at about 700-800Hz frequency. The pulses, containing harmonics up to the MHz region, can be injected into audio or radio-frequency stages of amplifiers, receivers and the like for testing purposes. A high-pitched....
-
The circuit comprises simply the PWM source, capacitor C, and resistors RD and RW. For CMOS circuits, you calculate the open-circuit output voltage as VCONT=D½§VDD, where VCONT is the control circuit`s output voltage, D is the PWM duty cycle, and VDD is....
-
Electromechanical door chimes can enhance your home, but they are vulnerable to costly repair problems. A defective pushbutton switch or a careless visitor can maintain the chime in an energized state for a prolonged period, thereby damaging the chime. The....
-
For designers of radar or sonar echo-ranging systems, an echo imitator can ease development and adjustment chores by generating a controllable pulse that's similar to an incoming echo signal. A decade ago, you'd probably use several 555 timers and their....
-
This circuit will allow you to turn on any piece of equipment that operates on 115 volts ac. The receiver circuit is based on the Radio Shack infrared receiver module (MOD), part number 276-137. It is also available from some of the other sources listed on....
-
You use a frequency discriminator to compare one signal frequency with another one. A functional feature, retriggering, of a monostable, one-shot 74xx123 multivibrator can yield frequency discrimination. Figure 1 shows a frequency discriminator that....
-
Recently, I have needed to measure inductances in the hundreds of microhenries to several millihenry range. Though I have a pretty good LRC meter and an excellent bridge on my workbench in Mesa, Arizona, I wanted to make these measurements in my home in....
-
The infra-red (IR) toggle switch project described here is aimed to provide control mechanism for electrical appliances that do not have remote operation features. The goal is to construct a black box where you can plug-in your 120V AC appliance and control....
-
The generators of square pulses, are used in a lot of applications, between which the adjustment of conditions of entry in the digital circuits and the control of amplifiers acoustic frequencies. This circuit is a generator that it produces, in combination....
-
There are several websites documenting the original Furby circuit board. I decided to replace the original circuit entirely and replace it with a PIC based controller. The mechanism of the Furby itself was designed around micro- controllers. It has one....
-
Power input is to a 7805 5 volt regulator. A pair of LEDs is connected between the 5 volt supply and ground, with current limiting resistors in series and one pin on the AT90S2313 shunts the current through one LED or the other. When one LED is on, the....
-
As you can see, there is only one regulated 12 volt supply operating the entire circuit. I was able to do this simply by AC coupling the received signal to U3 via C10. This allowed me to adjust the offset within an operating window. By using a tantalum....
-
When a processor-controlled device must operate reliably, designers often choose to periodically reset the processor rather than rely on a watchdog configuration. In low-power systems, this periodic-reset circuit can consume a large part of the system`s....