- Home /
- Search about irf
Page 1 about irf | |
Total Found: 128 |
-
Explanation Here is a simple 100-watt using IC CD4047 and IRF540 MOSFET of the inverter circuit diagram. The circuit is simple, low cost, or even assemble a veroboard. CD 4047 ..
-
This amplifier delivers 20 W into an 8-D load using a single IRF520 driving a transformer coupled output stage. This circuit is similar to the audio output stage used in many inexpensive radios and phonographs. ..
-
The laser diode·pulser is a simple drive circuit capable of driving the laser diode with 10-A, 20-ns pulses. For a 0.1 % duty cycle, the repetition rate will be 50 kHz. A complementary emitter follower is used as a driver. Switching speed is determined by....
-
The headlight flasher is nothing more than a 555 oscillator/timer that`s configured as an astable multivibrator (oscillator). Its input is used to drive the gate of an IRF53IND hexFET, which, in turn, acts like an on/off switch, ..
-
The circuit uses an IRF740 MOSFET which is rated at a maximum DS V value of 400V. The avalanche voltage is calculated as 3520 1. max DSA VV V. This means that up to about 500V of inductive kickback voltage can develop in the switched coil. More than....
-
The circuit described here uses an IRF840 MOSFET which is rated at a maximum DSV value of 500V. The avalanche voltage is calculated as 36501. max DSA VV V. This means that up to about 600V of inductive kickback voltage may develop in the switched coil.....
-
If TIP32C (Q2) gets excessively hot, use an IRF9640 MOSFET instead. Experiment with different values for R6 to find the optimal value (I use a 390 ohm resistor). Temporarily substitute R6 for a trim potentiometer (470 or 1k) to find the optimal dumping....
-
Here is a simple code for reading tags from the id12 RFID reader. It should be quite easy to modify if you know the dataformat your reader is sending out. Here is how to hook it up for serial communications, either using a microcontroller like arduino or....
-
This simple low power dc to ac inverter (dc to ac converter) circuit converts 12V DC to 230V or 110V AC. By doing simple modification you can also convert 6V DC to 230V AC or 110V AC. It can be used as inverters for home needs to enable light loads (electric....
-
The high voltage power supply was probably good for 12 to 30 kVDC at 1 or 2 mA. This is useful for many high voltage experiments, plasma globes, negative ion and ozone generators, bug disintegrators, starters for really LARGE HeNe lasers, etc. The devices,....
-
IRF9540N Gate Charge Test Circuitis schemed in the diagram below. IRF9540N is known to be rectifier device with advanced processing techniques to achieve extremely low on resistance per silicon area, according to the datasheet. Other thanGate Charge Test....
-
This circuit is a Mosfet-based linear voltage regulator with a voltage drop of as low as 60mV at 1A. The circuit uses a 15V-0-15V transformer and employs an IRF540 N-channel Mosfet (Q1) to deliver the regulated 12V output. The gate drive voltage required for....
-
In this circuit, four IRF510 power FETs are driven by a CMOS counter to generate the necessary two-phase drive quadrature. Although ICs are available to do this, this approach is handy for the experimenter because it uses commonly available parts. The....
-
I`m using H-bridge with IRF740 (MOSFET) to convert 315VDC to 230VAC. But the upper mosfets are frequently get damage within few seconds. I can`t find....
-
The nitrogen (N2) laser produces intense extremely short (a few ns) intense (100 kW typical) pulses of light in the near UV portion of the E/M spectrum (337. 1 nm). Despite this impressive capability, the N2 laser is among the easiest to construct for the....
-
The Pulsed Multiple Gas (PMG) laser described in this chapter is very similar in many ways to the Home-Built Pulsed Argon and/or Krypton (Ar/Kr) Ion Laser from Scientific American. However, the developers of the PMG laser have also used it with xenon (Xe)....
-
The 60 Watt linear amplifier is simple all solid state circuit using power mosfet IRF840. The IRF series of power transistors are available in various voltage and power ratings. A single IRF840 can handle maximum power output of 125 watts. Since these....
-
Hi all, I completed my first amp a few months ago. It was more a test than really something to listen to. It used the 9240/240 Mosfets. Now I want to....
-
This circuit is a Mosfet-based linear voltage regulator with a voltage drop of as low as 60mV at 1A. The circuit uses a 15V-0-15V transformer and employs an IRF540 N-channel Mosfet (Q1) to deliver the regulated 12V output. The gate drive voltage required for....
-
This be power motor controller 12V circuit. with a signal MCU Control be high class voltage , about 3V. It can motor control turn advance or walk go backwards...
-
The drive circuit of electromotor includes a FET bridge circuit, FET base drive circuit,current sensor of motor drive circuit and the relay. FET bridge circuit mainly consists of four high-power MOSFET power tubes,it requires that the power tubes have good....
-
The carbon dioxide (CO2) laser is the powerhouse for high tech industrial cutting and welding of metals and many other materials. Small CO2 lasers are used for marking of metal, wood, and composites, and in medicine and surgery. Even a `small` CO2 laser....
-
This has been the first Mosfet power amplifier of me, It is the most complete circuit. As a 60 watt power amplifier, this is sufficient for normal use in my....
-
Electric locos derive tractive effort from Traction Motors which are usually placed in the bogie of the locomotive. Usually one motor is provided per axle but in some older generation of locos two axles were driven by a single Traction Motor also. However....
-
The supply rails prudentially voltage was kept at the rather low value of + and - 40V. For those wishing to experiment, the supply voltage rails could be raised to + and - 50V maximum, allowing the amplifier to approach the 100W into 8 Ohm target. ..
-
Output transformer core: coming from flea market, light blue color, marked as A-438281-2-9H9-3, OD = 47 mm, ID = 24 mm, height = 13 mm. No information about µ Mosfet to be used: coming from flea market, with the following characteristics. It`s an obsolete....
-
Some months ago I ordered a EM-406 GPS module from Sparkfun. I intended to explore geotagging and this module seemed to be a simple one to use : integrated antenna, SiRF III chipset (seems to be well know on forums) while not too expensive. You provide a 5V....