60 kHz transformer consists of a 18 x 11mm ungapped pot core (Siemens, Fer-rocube, etc), utilizing magnetics incorporated type "F" material wound with SOV2 turns of No5 wire for the secondary and turns for the primary..

This power supply delivers plus and minus 9 V to replace two 9-V batteries. The rectifier circuit is actually two separate full-wave rectifiers fed from the secondary of the transformer. One full-wave rectifier is composed of diodes D1 and D2, which....

One of the control circuit"s triacs selects the tap on main transformer Tl, which provides the proper, preregulated voltage to the secondary regulator. T2 and its associated components comprise the secondary regulator. The ADC 0804, IC1, digitizes a....

Ll and L2 form a tuned transformer. About a 1:3 turns ratio is optimum. L2 and CI tune to the desired frequency. The fre..

This reciever uses the TDA1072A which is a complete AM reciever on a chip and it only requires comparitively few peripheral components to complete a high quality AM radio Circuit. Unlike some other AM radio ICs, a minimum number of external tuned inductors....

The spark developed by the circuit is suitable for a gas ignitor. Capacitor Cl is charged through Rl and Dl toward peak line voltage. C2 is simultaneously being charged at a slower rate through R5. When the charge on C2 is sufficient.to trigger the PUT,....

By adding a flyback winding to a buck-regulator switching converter (see the figure), wliich is essentially a 5-V supply with a 200-mA output capability, a 12-V output ) can be produced. The flyback winding on the main inductor (forming transformer Tl)....

The circuit provides a minimum component intercom. With switch SI in the talk position, the speaker of the master station acts as the microphone with the aid of step-up transformer Tl. A turns ratio of 25 and a device gain of 50 allows a maximum loop gain of....

This inverter uses a 12.6-V to 120-V transformer to deliver a quasi-sine wave that has the same rms and peak voltage ..

Diode Dl prevents negative spikes from occurring at the MOSFET gate, the 100 ohm resistor is a parasitic suppressor, and Z1 serves as a dissipative voltage regulator for the output and also clips the drain voltage to a level below the rated power FET....

Using two 12-V filament or power transformers, an impromptu isolation transformer can be made for low-power (under 50 W) use in testing or servicing. SOI is an ordinary, duplex ac recept-able. ..

This circuit provides a very low cost method of controlling light levels. Circuit power is obtained from a relatively high source impedance transformer or motor windings, normally used to drive the low-voltage lamps used in these functions. It should be....

This simple circuit gives a positive and negative supply from a single transformer winding and one full-wave bridge. Two zener diodes in series provide the voltage division and their centerpoint is grounded..

This linear amplifier delivers 10-W PEP output; with 1.25-W drive on 10 m. Tl, T2, and T3 are 10 turns of bifilar windings on an FT-50-43 toroidal core. The transformers are broadband. Filters for other bands, if desired, are shown. Note: use #26 wire for....

This supply is powered by a transformer operating from 120 Vac on the primary and providing approximately 20 Vac on the primary, and providing approximately 20 Vac on the secondary. Four 10-A diodes with a 100 PIV rating are used in a full-wave bridge....

This power supply is dedicated for use with rf equipments like, linear amplifiers, transmitters, receivers, and in every application that clean an-noisy signal is required. The circuit is very simple and you can drive it with a 220V/18V/3A transformer at the....

One v;ay to provide good negative-voltage regulation is with a low-dropout positive-voltage regulator operating from a well-isolated secondary winding of switch-mode circuit transformer. The technique works with any positive-voltage regulator, although....

Basically, this circuit is an adjustable electronic circuit breaker, containing a toroidal transformer that senses 60-Hz load current. Tl has a two-turn winding for primary, and 100 turns of #30 gauge wire for the secondary. A high-low range switch selects....

Amplify or record a telephone call with the simple circuit shown. The 8-0 secondary winding of a miniature transistor output transformer is connected in series with either of the telephone lines. ..

The burglar chaser makes a great accessory for any alarm system. It creates brilliant flashes of white light and a loud, irritating sound from a metal horn buzzer. Transformer T1 is connected to Ql, Rl, and R2 to form a blocking oscillator. This creates a....

In this circuit. a negative output voltage de-de converter generates a -5 V output at pin A. In order to generate -5 Vat point A, the primary of the transformer must fly back to a diode drop more negative than -5 V. If the transformer has a tightly coupled....

The circuit consists of a multivibrator (Ql & Q2), and a low power output stage Q3. The speaker should have an impedance in the region of 40 to 80 ohms. To use a low impedance speaker, connect an output transformer from the emitter of Q3 to ground. Cl and C2....

This circuit, can deliver 3 A or more and a maximum dc voltage ol` a little over 20 V. It is designed around the readily available LM317T adjustable 3-terminal regulator and has a pnp power transistor to boost the current output. The transformer has an 18-V....

Ul is a dual voltage comparator with open collector outputs. The A side is an oscillator operating at 100kHz, and the B side is part of the regulation circuit that compares a fraction of the output voltage to a reference generated by zener diode D2. The....

The design shown is a simple unit for QRP operation on all authorized frequencies up to 30 MHz. based on a toroidal transformer Tl. The secondary winding of Tl samples a small amount o1 rf power. both forward and reflected, which is divided by the bridge....

The circuit uses the primary current of a small 6 volt filament transformer to actuate a triac and energize the load. When switch Si, in the six-volt secondary, of the transformer is open, a small "magnetizing" current flows through the primary winding. This....

The simple circuit transforms the steady beep of an audible-signal device, such as a Mallory sonalert, into a distinctive warble or chirp. The value of R, C2 determines just what tone color you"ll get. With 1k the 1-I"F value shown, the circuit produces....

When the water level is low, the probe is out of the water and SCRl is triggered on. It conducts and imposes a heavy load on transformer Tl"s secondary winding. That load is reflected back into the primary, gating triac TRl on, which energizes the load. If....

The circuit has a "floating" output, i.e., it behaves like an isolated transformer winding, with the output amplitude remaining unchanged whether the center or either end of the load is grounded. This is achieved by making Z-out, common mode, infinite. The....

A center-tapped 240-V transformer is used with two SCR devices to provide rectified ac (pulsating dc) to MOT1...

A schematic diagram for the remote analyzer is shown. The circuit is powered from a simple 5-V supply, consisting of PL1, SI, Tl, a bridge rectifier (comprised of D1 through D4), capacitor CI, and a common 5-V regulator, Ul. Switch SI is the on/off control....

This broadband amplifier covers the 225-400 MHz military communications band producing 10 watt RF output power and operating from a 28 volt supply. The amplifier can be used as a driver for higher power devices such as 2N6439 and MRF327. The circuit is....