This is another 100watt inverter circuit diagram. Built based on IC CD4047 and Mosfet IRF540, this inverter have ability to supply electronic device -which require 220VAC-  up to 100w from 2-3A transformer....

This chapter contains circuit diagrams for several power supplies for pulsed solid state lasers. These include units suitable for driving the popular Hughes ruby and YAG rangefinder laser assemblies as well, one using the flash from a disposable pocket....

This chapter provides detailed schematics of a variety of power supplies suitable for use with the common Ar/Kr ion tubes available to the hobbyist on the surplus market. Included are examples of commercial designs (Omnichrome 150R and 532 head, Lexel 88 and....

R1 and R2 form a voltage divider, insuring that the phone line sees a high impedance load and that high voltages (such as the ring voltage) are easily dissipated by the protective diodes (CR1 and CR2). Also (obviously) they serve to divide all incoming....

The CDI ignition circuit produces a spark from an ignition coil by discharging a capacitor across the primary of the coil. A 2uF capacitor is charged to about 340 volts and the discharge is controlled by an SCR. A Schmitt trigger oscillator (74C14) and....

The IR2156 incorporates a high voltage half-bridge gate driver with a programmable oscillator and state diagram to form a complete ballast control IC. The IR2156 features include programmable preheat and run frequencies, programmable preheat time,....

This simple circuit uses an incandescent lamp to detect airflow. With the filament exposed to air, a constant current source is used to slightly heat the filament. As it is heated, the resistance increases. As air flows over the filament it cools down, thus....

Here's a circuit to create a buzzcoil using a standard automotive ignition coil. A 556 dual timer is used to establish the frequency and duty cycle of the coil current. One of the timers is used as an oscillator to generate the 200 Hz rectangular waveform....

The IR2166 Demo Board is a high efficiency, high power factor, fixed output electronic ballast designed for driving rapid start fluorescent lamp types. The design contains an EMI filter, active power factor correction and a ballast control circuit using....

The circuit is built around the IR2520D Ballast Control IC. The IR2520D provides adjustable preheat time, adjustable run frequency to set the lamp power, high starting frequency for soft start and to avoid lamp flash, fault protection for open filament....

The circuit is powered by the receiver's pack, the current drain is low, specially if compared to drain of servos. U1a VZ2 and Q1 are the CURRENT source of the sensor VZ2 is temperature compensated, use the listed component except for Q1 there you can use....

The CFL-2 is an electronic ballast design for driving a 42 watt compact fluorescent lamp from a 120 or 230 volt AC line. The circuit was designed using the IR2156 Ballast Driver IC. The main features of the circuit are programmable frequency, preheat....

The 555 is wired as an astable and the capacitor is charged only through the 4,7Kohm trimmer (notice the diode) and discharged only through the 2.2 Kohm trimmer, making the duty cycle full adjustable. The square wave is then feed in a totem pole made up of a....

This headphone buffer is based on Greg Szekeres' MOSFET Headphone Driver. It is a robust and reliable zero feedback, class A circuit. [Editor: And like the Szekeres MOSFET amp, this amp has unity voltage gain. Therefore, the audio source must supply adequate....

In this circuit the switches are power MOSFETs driven to conduct alternately by windings on a current transformer. The primary of this transformer is driven by the current in the lamp circuit and operates at the resonant frequency of L-C. Unfortunately,....

Hot wire foam cutters are used by hobbyists of all stripes to contour Styrofoam into a vast array of shapes for a wide variety of uses. Model railroad builders shape foam into landscapes. RC plane builders shape foam into aircraft wings and fuselages.....

The 60 Watt linear amplifier is simple all solid state circuit using power mosfet IRF840. The IRF series of power transistors are available in various voltage and power ratings. A single IRF840 can handle maximum power output of 125 watts. Since these....

A complete digital dimming system includes the dimming ballasts and a digital control unit for converting information from an Ethernet connection to the communication protocol required by the micro-controller in each ballast (Figure 1). Applications for....

This is a variation on the astable multivibrator. Circuit was recently developed to test for N-mosfets(the power kind e.g irf830). I don?t claim circuit can test all bad mosfets or all fault mosfet conditions. If mosfet is working it will operate in the....

The IRISMPS5 is an open frame 90W Flyback power supply unit (psu) using the IRIS4015 Integrated switcher. This demo board aims to show the capability of the IRIS4015 to handle the upper level of flyback topology power range, without the strict standby power....

This device uses a PIC12F615 to implement a capacitor discharge ignition system. When the switch (button) is closed, the PIC sends pulses to the IRF644 MosFet creating high voltage pulses to charge the 1.0 uf/250 volt capacitor. The voltage is read back via....

The Digital Addressable Lighting Interface (DALI), international standard prlEC929, is a communication protocol and method to interface lighting units on a 2-wire network. The DALI protocol is 16 bits and supports addressing up to 64 ballasts individually,....

The IRPLCFL5E reference design is an electronic ballast for driving 26W compact fluorescent lamps from 220VAC. The circuit provides all of the necessary functions for preheat, ignition and onstate operation of the lamp and also includes the EMI filter and....

The IRPLLNR2 is a high efficiency, high power factor, fixed output electronic ballast designed for driving rapid start fluorescent lamp types. The design contains an EMI filter, active power factor correction and a ballast control circuit using the....

The 555 is wired as an astable and the capacitor is charged only through the 4,7Kohm trimmer (notice the diode) and discharged only through the 2.2 Kohm trimmer, making the duty cycle full adjustable. The square wave is then feed in a totem pole made up of a....

The 60 Watt linear amplifier is simple all solid state circuit using power mosfet IRF840. The IRF series of power transistors are available in various voltage and power ratings. A single IRF840 can handle maximum power output of 125 watts. Since these....

The IRPLLNR1 is a high efficiency, high power factor, non-dimmable electronic ballast designed for linear fluorescent lamp types. The design contains an active power factor correction circuit for universal voltage input and a ballast control circuit....

Fan noise is becoming a significant issue as electronic equipment increasingly enters the office and the home. Noise is proportional to fan speed, and the airflowhence, fan speednecessary for cooling is less at low ambient temperatures. Because ambient....

This reference design is a high efficiency, high power factor, digital dimming electronic ballast designed to drive rapid start fluorescent lamp types. The design contains an active power factor correction circuit for universal voltage input as well as a....

The circuit is a MOSFET based linear voltage regulator with a voltage drop of as low as 60 mV at 1 ampere. Drop of a fewer millivolts is possible with better MOSFETs having lower RDS(on) resistance. The circuit in Fig. 1 uses 15V-0-15V secondary from a....

Virtually all domestic and professional dimming systems are based on triacs. These devices will conduct once they have been fired, only while current flows in excess of the holding current of the device. These dimmers work very well with a resistive load....

The IRF820 MOSFET has a voltage rating of 500v, it should work well in preamp stages of most tube amps. The 100 ohm resistor is there to suppress H.F. oscillations. If IRF820 is physically close to the 12AX7 plate, you probably won't need it. You can see how....