- Home /
- Search about 200W HIGH POWER AUDIO AMPLIFIER CIRCUIT
Page 700 about 200W HIGH POWER AUDIO AMPLIFIER CIRCUIT | |
Total Found: 22430 |
-
A special category of preamplifiers, they are the preamplifiers that undertake they amplification the low exit of Moving coil head, so that its drive to a input PHONO [RIAA] of preamplifier. With the moving coil heads, exist certain problems which it should....
-
The volume control in a hi-fi amp or preamp (or any other audio device, for that matter), is a truly simple concept, right? Wrong. In order to get a smooth increase in level, the potentiometer (pot) must be logarithmic to match the non-linear characteristics....
-
An In Circuit Programmer is a very valuable tool. Not only does it allow you to program you AVR's with ease, you can update your program without having to remove the AVR (very use full when working with surface mount devices). Also, an ICP allows you to use....
-
This firmware is intended to run on Atmel ATmega163 (499 bytes for program memory) or AT90S8515 (298 Bytes for program memory). Communications with the terminal is via RS-232 at 9600 baud. Use 8 data bits, 1 stop bit, and no parity. The RXD pin and TXD pin....
-
As I used this probe last nigh to determine if a 384 MHz oscillator was really working or not, I remembered email I received a while ago, asking how to make a field strength indicator without the microcontroller. Thus this page. If you want the auto zero....
-
A compact, inexpensive and low component count telecom head- set can be constructed using two readily available transistors and a few other electronic components. This circuit is very useful for hands-free operation of EPABX and pager communication. Since....
-
Many modern audio recorders is now compatible with digital input S / PDIF (Sony / Philips Digital Interface). Devices like CD Changers, MiniDisc recorders, computer sound cards and the like. working with digital signal just with protocol S / PDIF. Digital....
-
Basically, this is a frequency-current converter. It is used as frequency meter. Calibrating it can be used as tachometer. Please be aware this is an experimental project, I didn't use it connected on any vehicle but it should work fine after calibration. It....
-
A microphone amplifier that may be used with either Electret Condenser Microphone (ECM) inserts or dynamic inserts, made with discrete components. Both transistors should be low noise types. In the original circuit, I used BC650C which is an ultra low noise....
-
This circuit features an intermittent siren output and automatic reset. It can be operated manually using a key-switch or a hidden switch; but it can also be wired to set itself automatically when you turn-off the ignition. By adding external relays you can....
-
When you need a precision peak detector, you would usually implement it with one or several op amps and a few other associated components. This technique usually works well unless your design requires operation higher than a few kilohertz. In designs....
-
The generators of square pulses, are used in a lot of applications, between which the adjustment of conditions of entry in the digital circuits and the control of amplifiers acoustic frequencies. This circuit is a generator that it produces, in combination....
-
(Almost) Trivial application of an AT90S2313 or ATtiny2313 in an alarm clock to change the alarm from "BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP..." to "WAKE UP" in Morse code. This was designed in response to a request and is in daily use. An inexpensive....
-
Many times exists the need recording some conversations from a telephone line and this it's relatively easy. If we want however to have the possibility recording from two telephone lines simultaneously in a tape recorder, we needed a circuit as what appears....
-
The solar-lantern circuit in Figure 1 is a low-loss configuration that uses a 7W, four-pin CFL (compact fluorescent lamp) and a 12V, 7-Ahr, sealed, maintenance-free battery. The inverter features greater-than-85% efficiency, less-than-2-mA quiescent current,....
-
Diode detectors are good at changing AC into DC, even at high frequencies. The main problem with diode detectors have inherent nonlinearities, particularly for small signals. To minimize the effects of the nonlinearities, a preamplifier boosts the amplitude....
-
If you decide to use 2 circuits, i just connect their outputs together...neg output from first circuit to neg output of second circuit & pos output from first circuit to pos output of second circuit. And take readings from same place....from where you....
-
This circuits allows you to use a cheap loudspeaker as a microphone. Sound waves reaching the speaker cone cause fluctuations in the voice coil. The voice coil moving in the speakers magnetic field will produce a small electrical signal. The circuit is....
-
-
Creating a modular, networked, home control system was greatly simplified by using common 4-wire phone cable with stake-on connectors. The cable feeds both power and network signals to the various modules. Each module is made on a single sided circuit board....
-
There are several websites documenting the original Furby circuit board. I decided to replace the original circuit entirely and replace it with a PIC based controller. The mechanism of the Furby itself was designed around micro- controllers. It has one....
-
The LT®6700 dual comparator incorporates features to reduce part count in space-critical designs, including a trimmed on-chip 400mV bandgap derived reference and internal hysteresis mechanisms. The LT6700 also features low voltage micropower single....
-
This circuit sends MIDI program changes. It's useful as a guitar pedalboard remote...
-
It is well know that pests like rats, mice etc are repelled by ultrasonic frequency in the range of 30 kHz to 50 kHz. Human beings can't hear these high-frequency sounds. Unfortunately, all pests do not react at the same ultrasonic frequency. While some....
-
Power input is to a 7805 5 volt regulator. A pair of LEDs is connected between the 5 volt supply and ground, with current limiting resistors in series and one pin on the AT90S2313 shunts the current through one LED or the other. When one LED is on, the....
-
The entire circuit is powered from a very simple regulated +-15V power supply, that is able to deliver about 2 A continuous duty, and at least 6 A on musical peaks. Two three-terminal regulators with power transistors wrapped around them do the regulating....
-
This circuit, enclosed into a small box, is placed in the fridge near the lamp (if any) or the opening. With the door closed the interior of the fridge is in the dark, the photo resistor R2 presents a high resistance (>200K) thus clamping IC1 by holding....
-
One application is where you need a Higher Power Zener, Possibly even a 100 watt rating. Another useful application is as a Shunt Regulator for Solar Cells that are used to charge "Lead Acid Batteries". Simply Place it in parallel with the Solar Cell....
-
As you can see, there is only one regulated 12 volt supply operating the entire circuit. I was able to do this simply by AC coupling the received signal to U3 via C10. This allowed me to adjust the offset within an operating window. By using a tantalum....
-
Using a standard PLL circuit, such as the CMOS 4046B with some passive components, is a well-known way to design a clock multiplier. Unfortunately, using a PLL in a digital circuit has two disadvantages: It takes a long time for the circuit to reach a stable....
-
The circuit presented here can be used for connecting two telephones in parallel and also as a 2-line intercom. Usually a single telephone is connected to a telephone line. If another telephone is required at some distance, a parallel line is taken for....
-
The SCHAER+ programmer is a programmer for PIC18 family from a PC parallel port (LPT). It is derivated from the SCHAER programmer I used to download my projects in PIC1684. The SCHAER+ programmer should be improved to use a USB connection, without any....