It is a simple and reliable system for processing human speech. It has the task of altering the tone of the human voice and making it heard as artificial, such as the voice of a robot that, as it is known, is produced by artificial means. This is an easy but....

Explanation Here is a simple fire alarm circuit based on an LDR fire detection sensor. Smoke generated during circuit generates an audible alarm, fire smoke in case of fire. Al..

LDR1, a cadmium sulphide (CDS) photoresistive cell is used as the lower leg of a voltage divider between Vcc and ground. The timer terminals 2 and 6 are connected to the junction of the photocell and SENSITIVITY control Rl. The resistance of the....

As dusk begins to -fall, the sensor (a cadmium-sulfide light-dependent resistor or LDR) operates a small horn to provide an audible reminder that it's time to turn on your lights. To turn the circuit off—simply turn your headlights on and the noise stops.....

The circuit is activated by an LED/photoresistor isolator (Ul), which is a combination of a light-dependent resistor (LDR) and an LED in a single package. That device was chosen because of its high isolation (2000 V) characteristic, which is necessary....

Meter Ml, a +/-50-uA zero-center D`Arsonval meter movement is driven by Ul, a TL081 FET op amp, through R3. The gain of Ul is set at 11 by Rl and R2, while capacitor 01 is used to restrict the bandwidth of Ul to 1.6 Hz. Power for the circuit is derived from....

The circuit can be used as a sensor that can trigger an alarm, without direct contact being made by the intruder. In this circuit, a visible or invisible light source radiates on the sensor, keeping the detection loop in what could essentially be called a....

This circuit has the CMOS IC doing double-duty performance. The first two inverters operate as a digital audio oscillator; the third operates as a low-gain linear audio amplifier. As the intensity of the light falling on photoresistor LDRl increases the....

The circuit"s threshold is set by resistor R2. When the intensity of the light falling on the LDR is lowered, resistance of ..

A cadmium sulfide photocell (LDR1, which is a light-dependent resistor) is connected to the base and collector of an npn transistor, Ql. When light hits LDR1, the internal resistance goes from a very high (dark) value to a low (light) value, supplying base....

Integrated-circuit Ul—an LF351 or 741 op amp—is used as a comparator to control the light. Resistors R2 and R3 provide a reference voltage of about 2.5 volts at pin 3 of Ul. When daylight falls on light-dependent resistor LDR1, its resistance is low:....

The circuit is built around an LM339 quad comparator, Ul, which forms the basis of a Schmitt trigger, timer circuit, and a window comparator. One comparator within the LM339 (pins 1, 7, 6), plus LDR1, R4, R5, R6 and R8, is used as a Schmitt trigger. The....

As shown, there are two corner frequency: Start frequency attenuation transition of several children F 1/27rC3 (Ri + R2); by the decay into a flat corner frequency, LI. l/2rTC3..

As shown in the simplified block diagram of the high sensitivity of the alarm circuit, wherein the photoresistor LDR and three ordinary resistor connected. Thus, when the light..

Children lost a phenomenon often happens, look around, the family should not have brought enormous suffering and economic losses; in addition, also points to unscrupulous child..

As shown in the circuit, there is the incident at the time, this circuit is connected with photoresistor LDR transistor is turned high or zero level. Amplification factor of tr..

As shown in FIG optical control circuitry for high-performance street. The circuit consists of a photoelectric conversion element LDR, comparator circuit IC1 (555), single stab..

This is an automatic light dimmer circuit. You do not need to dim the lights by yourself. It is so very convenient, because we use the LDR to detect external light. To control the Triac, and the brightness of the lamp next. Suppose low light so there is....

The circuit shown here is used to switch on a lamp when the tele- phone rings, if the ambient light is insufficient. The circuit uses only two ICs and it can be implemented very easily. A light dependent resistance (LDR), with about 5 kilo-ohms resistance in....

This circuit is an automatic street light controller. Sensors used to detect changes in light is LDR (Light dependent resistor), the working principle of Light dependent resistor is exposed to light when the resistance value of LDR great, but if not exposed....

This is the fire alarm circuit which use LDR to sense the smoke from the fire, so it can be used to detect any dark smoke. With the onset of summer season, possibilities of fire accidents go up. These fire accidents could be prevented if ti....

When the sun position is changing so does the illumination level on the LDRs and the input voltage for the window comparator is no longer half of the supply voltage thereby the output of the comparator generates informations for the motor that rotates the....

The dark detector circuit shown here can be used to produce an audible alarm when the light inside a room goes OFF. The circuit is build around timer IC NE555. A general purpose LDR is used for sensing the light. When proper light is falling on the LDR its....

The receiver circuit in Figure 1 sounds an audio alarm when the transmitter (Figure 2) moves beyond a designated perimeter. The transmitter, a voltage-controlled oscillator, operates at approximately 915 MHz in the unlicensed ISM....

This be circuit warn when be become dark, or Light sensitive switch. By use electronics part the base is important , be the transistor 2N2926 and AC128. For...

This is a one of the light sensor. This circuit is a dark sensor that is based on op amp 741 IC as main control. This circuit is a simple design for sensor the light at the night. This is the figure of the circuit. For sensor the light is using LDR.....

This electronic organ is very simple to construct and can provide hours of enjoyment particularly for children. The circuit is basically an emitter-coupled oscillator composed of T2 and T3. An squarewave voltage can be sampled from the collector of T3(X2).....

Actually this part of the circuit is isolated from any other component (except via 5v & ground). Other than that, you can find LEDs and a shift register, but I guess they do not interact much. Or do they The ldr is used only as a light sensor. is there more....

Twilight Lamp Blinker circuit can be built with LDR and single IC circuit diagram with parts list of twilight lamp blinker various project using LDR and many more...

This circuit sent out an alarm when its LDR sensor is exposed to light by sun or lamp. A 555 astable multivibrator was used here which sent signal a tone of about 1kHz upon detecting light. The sensor when exposed by light completes the circuit and makes the....

Here`s a simple light activated police siren using light dependent resistor and NE555 timer. Before you make this project, I would recommend you to make the following projects. The 555 timer with R1=68K(say timer1) is configured in slow astable mode and the....

Reaction Capability Tester is used to test and train man s quick-response capability. It has various type of construction and the Reaction Capability Tester as shown in the picture is composed of decimal counter CD4017 and luminous diode. The construction of....