- Home /
- Search about voltage regulator circuit(0-30)
Page 55 about voltage regulator circuit(0-30) | |
Total Found: 5781 |
-
This figure illustrates a way in which a momentary 10-kV voltage pulse can be generated to initiate the plasma discharge across the laser tube. A Diode voltage-multiplier circuit is connected in series with the main supply and obtains its input power across....
-
Here is a `beeper` circuit employing two 555 ICs. It can be used in various circuits (having supply voltage of 5 to-15V DC) that require an alarm or a `beeping` signal. IC1 is connected in astable mode in the circuit in such a way that squarewave output at....
-
Voltage fluctuations in the mains are very common phenomenon. These fluctuations can cause heavy damage to costly electronics and electrical gadgets operating for long period of time. For such purpose, an automatic stabilizer is used which is usually quite....
-
This circuit provides a visual 9 second delay using 10 LEDs before closing a 12 volt relay. When the reset switch is closed, the 4017 decade counter will be reset to the 0 count which illuminates the LED driven from pin 3. The 555 timer output at pin 3 will....
-
Using the tester is easy, starting with power off, insert a transistor into the test socket. Set S1 for NPN or PNP androtate S3 to the required test position. Rotate VR1 so the desired collector emitter voltage. Pressing S2 now allows the measurement of hFE....
-
Through simple circuit modifications, designers can use peak current limiting to produce a constant current source....
-
Designed around the popular ZN414 ic this receiver covers the AM band from 550 - 1600 KHz with the values shown. For Longwave the coil needs to be changed. Use one from an old MW radio to save time. The ZN414 is a tuned radio frequency designed and....
-
The electronic switch is composed of the CK-4 type magnetic control switch and the VT1?R1?R2. When the bathroom door closes, the permanent magnet ZT and the reed pipe GA get close to separate the two touch tablets of GA, VT1 cuts off, pin-2 of IC has the....
-
A design for a synthesised ATV transmitter covering the 13cm band and beyond up to about 2. 6 GHz. This transmitter has been designed for optimum video performance and can achieve a broadcast quality signal when received with a professional TV microwave....
-
This circuit will convert a positive voltage to a negative voltage, while losing 1. 5 V (approximately). For example, if you`re supplying 9V to the circuit, the output will be -7. 5 V. This circuit can also be used as voltage doubler, by using the output as....
-
The circuit of this device is quite simple: an input circuit filters the signal provided by the antenna to reduce sensibility to other phenomena and protects against over voltages. The four transistors realize a "one-shot" section that is triggered by the....
-
This solar charge control combines multiple features into a single design: 3A current rating, low dropout voltage (LDO), range of voltage adjustment (accom....
-
This circuit adds some capacitors and diodes to a traditional transformer type series regulator circuit to extend the normal operating range. It can insure regulation during low line voltage conditions or it can squeeze a few more watts out of a....
-
Displays up to eight different DC voltages on CRT terminal of microprocessor under key-board control, using BASIC commands and BASIC routine given in article. Uses Motorola MC14433 modified dual-lamp integrating analog-to-digital converter. Unknown voltage....
-
C1=1000 Micro Farad aluminum electrolytic capacitor (For loads less than 100mA you can sustitute with 220 microfards capacitor), Voltage rating = 2. 5 times of Output Voltage. C1 = 1000 Micro Farad aluminum electrolytic capacitor(For loads less than 100mA....
-
This ultra-bright white LED lamp works on 230V AC with minimal power consumption. It can be used to illuminate VU meters, SWR meters, etc. Ultra-bright LEDs available in the market cost Rs 8 to 15. These LEDs emit a 1000-6000mCd bright white light like....
-
An overvoltage protection circuit is a circuit which protects electronics from excess voltage, which could potentially damage or destroy electronic components. In this project, we will build a simple, yet effective, overvoltage protection circuit using a....
-
This pdf file shows the schematic diagram of my home-built circuit to drive the PDR-56 probe. A JKL BXA-12579 inverter commonly used to drive cold-cathode fluorescent lamps is used as the high-voltage power supply. The BXA-12579 produces 1, 500 VACRMS for a....
-
The A1301 and A1302 are continuous-time, ratiometric, linear Hall-effect sensor ICs. They are optimized to accurately provide a voltage output that is proportional to an applied magnetic field. These devices have a quiescent output voltage that is 50% of the....
-
PWM waveforms are commonly used to control the speed of DC motors. The mark/space ratio of the digital wave-form can be defined either by using an adjustable analogue voltage level (in the case of a NE555 based PWM generator) or digitally using binary....
-
To power it up you need a clean stable source of 5 volts DC. This means that you either pick up a switching 5v DC power supply from our favorite JK Electronics, mail order one from Jameco or you will have to wire up a voltage regulator. Page 254 of Phys Comp....
-
Using a single 555 Timer IC and a small transformer to generate a high voltage, this circuit will test zener diodes of voltage ratings up to 50VDC. The 555 timer is used in the astable mode, the output at pin3 drives a small audio transformer such as the....
-
This version of the Link is for those who really need a good cheap intercom that will work reliably, but without access to an outside Telco line. This could be in a pre school, a hobby farm or a small workshop or factory, where external phone traffic needs....
-
The circuit diagram shown here is of a simple DC power delay circuit that is based on an SCR. This circuit is a very handy one and can be employed in many applications. The working of this circuit is very simple. When the input power is applied the capacitor....
-
Using the LT3692 dual current mode PWM step-down DC DC converter circuit with two internal 3. 5A switches can be designed a very simple power supply circuit, that can be used for various electronic circuits applications like : distributed supply regulations....
-
A milliamp meter can be used as a volt meter by adding a series resistance. The resistance needed is the full scale voltage reading divided by the full scale current of the meter movement. So, if you have a 1 milliamp meter and you want to read 0-10 volts....
-
Watch the video given below to get a better idea on how LED works A light emitting diode (LED) is known to be one of the best optoelectronic devices out of the lot. The device is capable of emitting a fairly narrow bandwidth of visible or invisible light....
-
A fan regulator circuit which can also be used as a simple lamp dimmer circuit.This fan speed regulator or light dimmer is based on power control using triac....
-
The 60 Hz Frequency Generator circuit is very urgently needed to make the inverter or hardware related to the AC current voltage. This 60 Hz Frequency Generator is very simple and has a high accuration, the squarewave as the output which is precision. The....
-
An unconventional, scalable high efficiency 12V solar power system and battery charge controller withlow voltage cutout to protect thebattery. (ideal for systems of 50W or less) This circuit was designed for small to medium lead acid systems and feature a....