- Home /
- Search about 3 Channel Color Organ (220V)
Page 383 about 3 Channel Color Organ (220V) | |
Total Found: 12403 |
-
This was designed to flash a pair of LEDs to be mounted on the wing tips of a Parkzone Citabria R/C (remote control) airplane. The unmodified Parkzone Citabria only weights 20 grams (about 0.7 oz), so weight, and therefore the number and size of the....
-
This is a design for a low noise microphone preamplifier, which is ideally suited to low impedance (600 Ohm nominal) microphones. One limitation is that it is not balanced, which is not a problem in a home recording environment, but will allow the mic lead....
-
This microcontroller fascinated me a lot because I wanted to see what we can do with an 8-pin microcontroller (out of which 2 pins goes to power supply, so actually just 6-pins are left for I/O). So I thought of making my own learning board for this. In this....
-
The System is fully controlled by the microcontroller AT89S52. It is a popular 8 bit microcontroller. The circuit consists of four switches, in which two buttons are used to increment and decrement the temperature value and the next button is to edit the....
-
A standard serial interfacing for PC, RS232C, requires negative logic, i.e., logic `1` is -3V to -12V and logic `0` is +3V to +12V. To convert a TTL logic, say, TxD and RxD pins of the uC chips, thus need a converter chip. A MAX232 chip has long been using....
-
A fast electronic fuse designed to operate on 230V AC with an adjustable trip current. When the current through the load exceeds a level determined by the position of the wiper on the 1k wire-wound pot, this circuit cuts off the load immediately. If S1 is....
-
Two soft start power supplies. The output voltage slowly increases to the desired output. The output voltage rises slowly and reaches 15 V in 5 seconds. In order to perform this soft-start function, the LM317 voltage regulator IC requires an external....
-
The hardware block is shown in Figure 1. The MCU is 89Sxx microcontroller. And the complete hardware schematic is shown in Figure 2. Port1 is used as data-bus for LCD (4-bit interface, PCB lay-out for 16x2 character with backlight), on-board tact switch and....
-
The design objective was to produce an hFE tester with switched collector currents for the DUT (Device Under Test) covering a range suitable for the selection and matching of output transistors for amplifiers such as the JLH Class-A, ESP DoZ etc. The tester....
-
The LEDs are OSSV53E1A from OptoSupply and they have an 140° angle. This means that the first plane with uniform density can be obtained at a shorter distance from the LED, for a given spacing between LEDs which means smaller height for the board. Their peak....
-
4 Channel Infrared (IR) Remote is a simple kit using the famous HT12A and HT12D encoder / decoder chips from Holtek...
-
To put the relay in tension the 4 buttons S1 S4 must be pressed. If anyone of the 4 butoons S5 S8 are pushed the relay donts tension ( dont receives supply voltage ). The supply voltage must be equal to the working voltage of the relay. One transistor....
-
This Remote control Jammer device it’s useful when we need to block someone to use the remote control (children that change frequently the channels at tv). This remote control jammer it’s very simply and it use two infrared Leds which continuously transmit....
-
Real-world measurement requires the extraction of weak signals from noisy sources. High common-mode voltages are often present even in differential measurements. The usual approach to this problem is to use an op amp or an instrumentation amplifier and then....
-
For many application there's no substitute for sheer power- low efficiency speakers, outdoor sound systems, or maybe you like the full flavour of the dynamic range of a high power amp. Whatever your requirement-this super power module should fit the bill.....
-
This is a rather unusual QRP Power Amplifier design, with a wide frequency response; within three dB's from 300KHz to 30MHz. Overall gain is in the region of 16dB and the final output power may be well over four watts. The wide bandwidth is a result of the....
-
In Figure 1, an MC34063A switching regulator and an MC33342 NiMH battery-charger IC combine to generate from an unregulated power supply a 600-mA battery charger for one to four NiMH cells...
-
My circuit adds a transistor, to add feedback, and two resistors, to tailor the range of the control, with the result that a single-turn potentiometer gives a control range of about 2 to 30 microamps. I installed my circuit in a small plastic box, and....
-
Because of the nixie-tube is a gas tube, it requires relatively high-voltage supply. Judging from archives, from 180 to 300 volts are used for supply voltage. In this project, 270 volts from rectified 100V line voltage directly is used. It is very simple but....
-
This current to voltage converter rely on the very high input impedance of the operational amplifier. The input current (I) is forced through feedback resistor (Rf), and generates an output voltage equal to (-I x Rf). This output voltage is valid for output....
-
This circuit measures temperature in Celsius scale and displays it on an alphanumeric LCD screen. When temperature rise to 40 C an alarm is activated and at the same time a relay is also activated which drives a fan to keep the temperature at a level.....
-
If this picture (above) looks a lot like the Pretty Good LC Meter also on this web site, that's because its the same meter, but with some significant improvements. At this point, its a good idea to read the Pretty Good LC Meter page because the rest of this....
-
Circ?it to close a relay when any phone extension is off-hook. Uoltage at the gate of the MOSFET sho?ld be negative (1-3 volts) with respect to the so?rce then phones are on-hook. Uoltage at the gate sho?ld be positive (8-113 volts) with respect to the....
-
The circuit of the transmitter is shown in Figure 1, and as you can see it is quite simple. The first stage is the oscillator, and is tuned with the variable capacitor. Select an unused frequency, and carefully adjust C3 until the background noise stops (you....
-
You can play this game alone or with your friends. The circuit comprises a timer IC, two decade counters and a display driver along with a 7-segment display. The game is simple. As stated above, it is a scoring game and the competitor who scores 100 points....
-
Very simple and useful circuit for communication between two person. The Q1 is used to amplify the weak output signal of speaker when one push his (her) side push-button to speak. The base-common configuration of the Q1 pre-amplifier is for matching low....
-
The Car Voltage Gauge is based on 3 parts. The input circuit is an Analog to Digital Converter (IC2 CA3162E). The purpose of this chip is to sample an analog voltage and convert it to a decimal value which is read by a Display/Decoder Driver (IC1 CA3161E).....
-
Speed controllers have long exploited the reverse-EMF characteristics of dc motors to control their speed. These linear driver circuits use power op amps to create a negative resistance drive to the motor that counteracts the voltage drop in the motor`s....
-
This circuit features clipping indicators on the preamp and reverb recovery stages, allowing for the optimal gain settings. The guitar input stage is a class A amplifier with adjustable bias. A 2N3906 PNP tranistor is used for a low noise design on this....
-
The simple circuit of Fig.1 emulates a similar conjuring trick which sells for hundreds of Pounds. The trick seems to do the almost-impossible from an electronic point of view, let alone from the point of view of common sense. It consists of a bank of....
-
This is an evaluation use of a small graphics LCD module. Last summer, SG12232C graphic LCD module has been sold sold for 1500 Yens from Akizuki Denshi and I bought it. However I could not find good application for the LCD module and it was going to go to....
-
This is a replacement power source for 1.3V mercury cells or other small batteries. It has many uses and I use this circuit in my computer to power a front panel multi adapter which has a digital thermometer...