- Home /
- Search about 3 Channel Color Organ (220V)
Page 386 about 3 Channel Color Organ (220V) | |
Total Found: 12403 |
-
The talking Yoda head consists of a Yoda mask and a microcontroller system to achieve the desired operation/effect. The basic operation of the project was specified as follows: The head was to be placed inside a closed box. Upon opening the box, the light....
-
This circuit provides 16 watts of amplification. it is built using two LM383 power audio amplifiers. use suitable heat sinks with the ic`s...
-
The circuit is very simple and incorporates darlington output transistors that will provide more than enough output current than is needed to drive a 3-ohm speaker. The gain may be pre-set for a variety of input levels, making it suitable for amplifying....
-
This is a very sensitive 50Mc converter allowing you to receive the entire "Magic Band" (50Mc...52Mc) on your general coverage receiver (28Mc...30Mc). It receives all types of modulated transmissions. It all depends on the receiver used. I`ve tested this....
-
Forget to turn off the ceiling fan in your bathroom? Install the simple timer in Figure 1. It`s located out-of-sight in the fan unit, and you turn it on via the wall switch. The circuit costs virtually nothing, using "junk" parts. When ac power appears, a....
-
For designers of radar or sonar echo-ranging systems, an echo imitator can ease development and adjustment chores by generating a controllable pulse that's similar to an incoming echo signal. A decade ago, you'd probably use several 555 timers and their....
-
Simplified circuit diagram of the two-stage Colpitts oscillator. In comparison with the classical single-transistor Colpitts oscillator [1,2,5] the two-stage modification includes an extra transistor Q2 and an extra capacitor C3. We note that both....
-
The transmitter runs on only 3V whereas most others run on more voltage. This dirt cheap item uses non-adjustable inductors so it is not possible to tweak for higher output. The common TX2B chip is manufactured by HIGHLAND (SHENZHEN) ELECTRONICS CO LTD and....
-
This circuit will allow you to turn on any piece of equipment that operates on 115 volts ac. The receiver circuit is based on the Radio Shack infrared receiver module (MOD), part number 276-137. It is also available from some of the other sources listed on....
-
The circuit in Figure 1 is an FPGA-based, synchronous FIFO that uses the same clock for read and write operations. The circuit can generate FIFO-occupancy flags with a minimum of logic. The boxed area in Figure 1 shows a more conventional occupancy meter.....
-
This ZIP file contains information about building a small radio transmitter, which has a PCB 1.75" x 2.5" (45mm x 68 mm) and has a range of about 30 yards or so. The documentation with the circuit says the freq range is 100-108 MHz, but I have found it to be....
-
The fins were added to a simple flat aluminium panel, and are made from 20 x 20 x 3mm aluminium angle. Their purpose is threefold - they improve the performance of the plate as a heatsink (although this is not necessary with the BP4078 PWM amp), they make....
-
In recent years, following CD`s introduction, vinyl recordings are almost disappeared. Nevertheless, a phone preamplifier is still useful for listening old vinyl discs from a well preserved collection. This simple but efficient circuit devised for cheap....
-
This circuit is designed to amplify the input from a telescopic whip antenna. The preamplifier is designed to cover the medium waveband from about 550Khz to 1650Khz. The tuning voltage is supplieb via RV2, a 10k potentiometer connected to the 12 Volt power....
-
You use a frequency discriminator to compare one signal frequency with another one. A functional feature, retriggering, of a monostable, one-shot 74xx123 multivibrator can yield frequency discrimination. Figure 1 shows a frequency discriminator that....
-
For the 60W amplifier, a nominal (full load) supply of +/- 35V is required, so a 25-0-25 secondary is ideal - however, see Updates, below. The circuit for the supply is shown below, and uses separate rectifiers, capacitors and fuses for each channel. Only....
-
Efficiency can be increased by using a germanium transistor at the 33 ohm current sense resistor, and by using a proper torroid core in place of the crappy ferrite bead. Single AA cell powers two LEDs at constant current....
-
Intelligently modifying the motor-drive commands to a robot can give you control finesse during competitions. Moving a joystick hard right, for example, might have different effects, depending on the robot`s speed and direction. Software running on an....
-
Early DACs contained standard R-2R ladder networks, and produced a negative output voltage. These early DACs, such as the MAX7837/7847 and the MAX523, require both positive and negative supply rails to accommodate their negative output. With the transition....
-
A functional block diagram is shown below and illustrates the primary circuit functions. These include equalization, reclocking, and driving 75W co-axial cables. A complete schematic is also included. The EB-RD35 accepts a serial digital data input....
-
The genesis for this hybrid electrostatic headphone amplifier occurred when I was in Hawaii on vacation, at a fancy hotel on Maui. Sitting at the bar on the beach, drinking "Blue Hawaiis," I drew the schematic for the amp on a placemat. The design is my....
-
The preamplifier that appears in the figure is a completely symmetrical preamplifier, from the input as the exit and it works in Class A. It does not have somebody innovation, simply it uses good solutions, in order the result is what should. Such proposal....
-
The new LTC1155 Dual Power MOSFET Driver delivers 12V of gate drive to two N-channel power MOSFETs when powered from a 5V supply with no external components required. This ability, coupled with its micropower current demands and protection features,....
-
It is a voltage regulator that allows a 6v portable supply to be derived from the 12v car battery. You can add a 6.2V zener diode and a LED to warn you when the input supply is overvoltage. If you could find a relay that would operate from 6.2v right up to....
-
Linear regulators are easy to implement and have better noise and drift characteristics than switching approaches. Their largest disadvantage is inefficiency: excess energy dissipated as heat. Several well-known techniques are available to minimize the....
-
In its simplest form, a voice-over unit is just a microphone and change-over switch feeding an amplifier, the output from the microphone having priority over the amplifiers audio signal when the "push-to-talk" switch is pressed. In this circuit, a....
-
The operation of a 303MHz circuit has been covered in our project WIRELESS DOORBELL. We are not going over how the circuit works but explain the importance of some of the components and how they effect the range. The most critical component is the....
-
This mini audio amplifier will test the audio stages in amplifiers such as the front end of FM bugs. You can also use it on lots of our other projects as well as the output stages of radios. It is a very handy piece of test equipment and will make a perfect....
-
The MAX6953 from Dallas Maxim is a compact cathode-row display driver that interfaces a microprocessor (like PIC or AVR) to four 5x7 dot matrix LED display trough an I2C compatible serial interface. The chip includes some features that can help us to handle....
-
This design reconfigures the APD-bias IC, IC1, to allow its low-voltage DAC output to modulate the high-voltage, current-sense feedback via a high-voltage-output transconductance stage comprising Q2 and Q3. These two complementary transistors provide....
-
This circuit us gives the sense of movement of ball up down, after the LED turn on successively the one afterwards the other. As soon as it reaches in the one or in the other end it makes again the opposite movement to behind. As clock are used two inverters....
-
The circuit is a MOSFET based linear voltage regulator with a voltage drop of as low as 60 mV at 1 ampere. Drop of a fewer millivolts is possible with better MOSFETs having lower RDS(on) resistance. The circuit in Fig. 1 uses 15V-0-15V secondary from a....