- Home /
- Search about UHF TRANSCEIVER
Page 10 about UHF TRANSCEIVER | |
Total Found: 315 |
-
This is an UHF band TV antenna preamplifier circuit With 15dB gain to build easily. It is formed based on BF180 UHF Transistor. The first stage is an band pass filter constructed by the C1, CV1, L1, L4, C7 and C3, the second stage is a base-common voltage....
-
Figure 1 shows the block diagram of a direct conversion RF receiver—the receiver demodulates an RF carrier directly into a baseband signal without an intermediate frequency down-conversion (a zero IF receiver). The antenna, shared by both the transmitter and....
-
This circuit will be of interest to the radio amateur and anyone posessing two radios, (one of which must be able to transmit i.e. a transceiver). It is a self powered (audio derived) repeater circuit for receiving a signal and re-transmitting it via the....
-
This is a prototype of the WA4DSY 56KB RF modem. It is intended for use on amateur packet radio networks. The modem generates RF in the 28 to 30 mhz range and requires and linear transverter to convert the signal to a UHF or microwave ham band. The digital....
-
Ham Radio (amateur radio) is a popular hobby amongst electronics enthusiasts all over the world. Basically the hobby involves a person in making his own gear consisting of a receiver and transmitter or a transceiver (a receiver and a transmitter in one unit)....
-
This project describes a little QRP transceiver full legal power” (5 W at 12 V) for the 40 meters band. The RIG may be built in a gradual manner, in fact it is divided in two main modules, or you may also complete only the RX module. The RX section is....
-
The PMR VHF transceiver Motorola Radius M110 (in further text referred as M110) was manufactured by Motorola GmbH therefore being an European radio. Since many professional radio service users has replaced this transceiver with newer gear, a considerable....
-
This circuit is designed to work at UHF frequencies in the range 450-800MHz. It has a gain of around 10dB and is suitable for boosting weak TV signals. The circuit is shown below...
-
Use for this antenna tube of 10mm diameter. Or you can use a brass rod of about 7mm diameter. The top one is a strong copper (brass) wire of 5 to 7 mm diameter soldered directly to the coil and mounted to the PVC isolator to give a strong construction...
-
Some RISC controllers, like the NEC V850 family, use an internal 32-bit architecture with an external 16-bit bus. The architecture also allows interfaces with 8-bit memories. However, with 8-bit memories, accesses to and from odd locations automatically....
-
The RS232 transceiver supports both RS232 and EIA-562 standards, whereas the RS485 transceiver supports both RS485 and RS422 standards. The logic input (MODE) selects between RS232 and RS485 modes. With three additional control logic inputs (RXEN, DXEN....
-
The Inter-Power SWR-5 - upper right - "isn't worth a penny". Got it from a mate to use with a beacon, but I burnt it out with only 3.5-4W morse signal on 70cm. Removed the bridge and installed my own pick-up line (suggested by LA8OJ) and now it is fb for....
-
An economical and commercially available quartz temperature sensor, Y1 and IC1, an LTC-485 RS485 transceiver in transmitter mode, form a Pierce crystal oscillator. The sensor, an Epson HTS-206, presents a nominal frequency of 40 kHz at 25°C and a temperature....
-
This was one of my very first transceiver developments. This page was also one of the very first circuit descriptions that I put on the internet quite some years agon. Today I would not build a transceiver like I did then, but it was working, so I have kept....
-
This is an improved version of the audio interface commonly used to connect a computer soundcard to a transceiver`s receive and transmit audio circuits. This kind of interface is used by computer programs that send and receive SSTV, RTTY, CW, PSK31 and....
-
The transceiver is composed by three single sided printed boards 100x70 mm, theese may be stacked so as to reduce the overall size of the metal cabinet. I suggest to employ small size components (1/4 W resistors, 2,5 mm capacitors, ) wich should fit....
-
This simple QRP transceiver for the 30 m band did not result from a detailed requirement profile. I simply had some NE592 broadband amplifiers in my junk box, waiting for an application. After performing some tests, that application was quickly found: The....
-
This PSU has been especially designed for current-hungry ham radio transceivers. It delivers safely around 20Amps at 13.8V. For lower currents, a separate current limiting output, capable of 15ma up to a total of 20A has been added. Let us see what we have....
-
I wanted a robust, portable, compact antenna usable for horizontal and vertical polarisation to take along with my FT-817 when I go on vacation, camping etc. I also wanted the dipole to cover the VHF and UHF bands and if possible with some gain! As everybody....
-
This true SSB transceiver is built around just 5 vacuum tubes, with no transistors nor ICs. Superhet receiver with AGC and S-meter drives a loudspeaker, 5W transmitter, very stable VXO uses CB crystals to cover 20m ham band. A project for skilled RF....
-
In general, the transceiver switches the 4-element 1500 ohm xtal BPF ends between the inputs and outputs of the two SA602s to reverse the signal flow for R/T operation. Since no IF amplifier is used in the design, 20 dB of additional receiver gain is....
-
This PSU has been especially designed for current-hungry ham radio transceivers. It delivers safely around 20Amps at 13.8V. For lower currents, a separate current limiting output, capable of 15ma up to a total of 20A has been added...
-
Simplified circuit diagram of the two-stage Colpitts oscillator. In comparison with the classical single-transistor Colpitts oscillator [1,2,5] the two-stage modification includes an extra transistor Q2 and an extra capacitor C3. We note that both....
-
This simple counter is useful for frequency measurements of various wireless equipments, especially transmitters, receivers and signal generators in VHF/UHF band...
-
The whole Construction : You can call the transceiver like this as "OZL type". Characteristics of the "OZL type" are as follows. 1. Single conversion super. 2. Using two DBM-s as modulator and converter. 3. Modulator DBM is used as demodulator in....
-
The elements diameter of the antenna may vary between 5...8mm and the dipole diameter may vary between 8...12mm (12mm recommended) without the need of changing anything to the length or spacing. All elements except the dipole are electrically connected to....
-
The circuit can be culled from the MCP2120 developer`s kit user`s guide. It is on page 51 of document DS51246A. If you don`t want to use an integrated transceiver, there is a circuit for you to build your own with a seperate ir led and detector. Make sure....