This circuit is an amplifier for small transmitters operating in the UHF band, specifically in the 450-800MHz range. The amplifier works in class A and we used the well-known Philips BLW33 transistor for its manufacture. The construction, although simple,....

This project is a construction of a VHF-UHF linear amplifier that can work at frequencies from 47MHz to 740MHz. It can be used as a final output stage of any transmitter working between these frequencies. It use the BFQ34 NPN a 4GHz wide-band transistor with....

As shown in Fig range is a frequency of 400 ~ 850MHz UHF amplifying circuit. Printed circuit For best performance and results, the circuit should be used by the silver tin processing...

This circuit offers 10- to 15-dB gain from 400 to 850 MHz and is therefore eminently suitable for situations where th..

This de adapter provides a regulated 9-V source for operating a Kenwood TR-2500 hand-held transceiver in the car. The LM317T"s mounting tab is electrically connected to its output pin, so take this into account as you construct your version of the adapter. ..

This circuit is useful in amateur radio VHF and UHF work where a mast-mounted antenna preamp is used for receiving. The kit controls T-R switching and change-over relay sequencing so that high RF levels are prevented ..

This small circuit is a Linear amplifier for driving small UHF TV transmitters. Its gain is 7dB and can amplify a signal between 450-800 MHz. You can drive the circuit with 1 to 1,5 Watts signal. Better use double layer PCB with the second layer connected to....

This circuit uses low-cost IN4148 diodes and exhibits about 1.5 dB insertion loss from 10 to 1000 MHz w..

An NE567 tone decoder, tuned to the transceiver"s CW offset frequency, ensures that the transceiver will be tran..

This FET probe has an input impedance of 10 M!J shunted by 8 pF. Eliminating the protective diodes reduces this impedance to about 4 pF. The frequency response of the probe extends from de to 20 MHz ( -1 dB), although higher frequency operation is possible....

The unit consists of a direct conversion receiver and 1-W transmitter. The direct conversion receiver VFO is tuned just off frequency from the incoming signal. This difference in frequency produces a clean, strong, and solid audio tone signal. Detect the....

Everytime the push-to-talk button is closed the light will go on. The antenna samples the output RF from the transmitter. That signal is then rectified (detected) by germanium diode Dl, and used to charge capacitor C2. The dc output is used to trigger a....

This circuit was designed to make switching of a 48-channel mobile transceiver safe to operate while mobile. The oscillators allow for single-stepping or a scanning function. The scan facility allows for stepping through all 48 channels to check for....

The LM1812 is a complete ultrasonic transceiver on a chip designed for use in a variety of pulse-echo ranging applications. The chip operates by transmitting a burst of oscillations with a transducer, then using the same transducer to listen for a return....

The UHF motion detector operates on the Doppler radar principle. Ql is an oscillator that creates a radiated signal. An..

This rf probe is coupled with a fiber-optiCJ:able to the test equipment. It utilizes inexpensive components to improve probe performance at UHF frequencies. The receiving antenna in this probe feeds an envelope-detector diode. After amplification by the....

The video master consists of a series of converters that place all your video sources on unused UHF channels, which then combines them with normal TV channels (terrestrial or cable into one cable). That one cable can then feed several TV sets for....

That Circuit is a UHF TV linear amplifier for small TV transmitters with output aroun 100-200mW. The transistor BGQ136 comes with SOT-122 case has gain of 13dB at 800MHz. So with input 100mW you get 2W output and for 200mW you get 4W...

This simple mobile voltage regulator circuit may save your two meter or CB transceiver if the voltage regulator fails. The 2N3055 should be heat sinked if current drawn by the rig is in excess of 2 A on transmit..

These are modulator circuits for modulation of video signals on a VHF/UHF carrier. The circuits require a 5 V power supply and few external components for the negative modulation mode. For positive modulation an external clamp circuit is required...

Combine an electrostatic transducer with an ultrasonic transceiver IC to build a ranging system that senses objects at distances from 4 inches to more than 30 feet. Transducer Yl "s broadband characteristic simplifies tuning. The secondary of T1 resonates....

To avoid grief when using 12-V power supplies with mobile transceivers, especially when there is a short -circuit failure of the series pass transistor, crowbar circuits provide protection by clamping the power line and blowing the fuse within microseconds....

The MAR-x preamp shown will cover up to 1.5 or 2 GHz with the correct MAR-x IC. ATTN1 should be omitted for low noise-figure.appli cations. ATTN1 and ATTN2 provide a means of limiting possible termination range,..

This is a 3-W, single-circuit board, VFO-controlled CW transceiver for 40 or 30 meters, featuring a direct-conversion receiver with audio filtering, Receiver Incremental Tuning (RIT), and speaker level audio volume. The transmit frequency is generated by....

The transceiver mixer and carrier oscillator in the band-imaging (7- and 14-MHz) CW transceiver. Careful selection of ..

The LM383 is an audio-power amplifier that is capable of producing up to 8 W of audio output. R1 is essentially a load resistor for the hand-held transceiver"s audio output. R2 can be composed of two fixed resistors in a 10:1 divider arrangement, but using....

This transceiver has a 3-stage transmitter and a direct-conversion receiver. Ql is the transmitter"s oscillator, an..

The oscillator is a standard UHF design which delivers about 10 mW at 1.2 GHz. R1 and R2 bias the base of Q1 to 1.2 V via 12. Collector current is set by R3 to about 30 mA. C2 couples the base of Q1 to the stripline circuit. Tuning is provided by CVl, and....

This structure is an amplifier RF, covering the range of UHF and intended for small TV transmitters, working in the channel UHF. The amplifier can enhance any video signal to the region UHF (450-800MHz). The circuit operates in class A and uses the known....

The antenna tunning circuit can accommodate 1/2 wave length antennas or higher, for input resistances of 50 Ohms which make it suitable for CB (Citizen Band) transceivers. C1 is for fine tunning and C2 is just for tunning. Turning C3 with the help of C2....

This circuit utilizes the MRF123 TMOS power FET. The MRF134 is a very high gain FET that is potentially unstable at both VHF and UHF frequencies. Note that a 68-0 input loading resistor has been utilized to enhance stability. ..

The following circuit shows about Video and DVD Modulator in VHF / UHF Circuit Electronic Diagram. Features: oscillator uses a transistor for high ....