- Home /
- Search about circuit breaker
Page 356 about circuit breaker | |
Total Found: 19494 |
-
A regulated 5 volt DC supply is essential for powering micro-controller and TTL based circuits. The output of most wall-warts and adapters is to rippled and impure for use in digital circuits. Lets build an inexpensive power supply using some discrete....
-
A flip-flop that generates two unstable states (high-low) is called astable multivibrator, a fancy name for you to say it`s an oscillator. The very basic of....
-
As shown in Figure it is 567 FM demodulation circuit. In the figue, the FM signalenters from the 3 foot, the demodulated signal goes out from 5 foot. FM signal center frequency which the circuit can demodulateis: fo = 1.1 / RC, C1 isfilter capacitor, and C2....
-
This circuit employs a synchronous demodulator to separate a 1 KHz signal from noise and measures the amplitude with the 1 kHz signals when a 2nd at about 60 microvolts per count then sends the measurements via an RS-232 interface for further processing or....
-
A well tuned antenna system works like a dummy load, i. e. the SWR is 1. 2:1 or below but the hunting range is low. What`s wrong Insufficient radiation How to know that Yes, this is what the article about. You can measure the effective radiation using a....
-
We aim to transmit more information by carrying articles. Please send us an E-mail to wanghuali@hqew. net within 15 days if we are involved in the problems of article content, copyright or other problems. We will delete it soon. ..
-
This circuit and a simple series circuit Tone Control. This circuit tone control with surgical Amp LM301A. The JFET 2N3684 feature provides a high input impedance and low noise for UN buffer zone opinion operational amplifier operated EQ type. Could you see....
-
After all job of building the prototype and making the sketch work, it`s the time to build the circuit. It`s not the objective to explain in detail how to make printed circuit boards, but only a superficial explanation about it, besides, of course, to....
-
Circuit The picture shows the circuit diagram of a rotation sensor that can turn on a device like motor or buzzer while the circuit assembly rotates. The circuit is based on basic 555 timer operation. ..
-
This is a constant current source using a FET. This is the most simple replacement to series resistor to limit current. The N-Channel FET BF256C can give 15mA current. Simple Methods Before you get to use chips, experiment with some methods, which will help....
-
You`ve probably heard about the CP210x USB ICs from Silicon Labs, now here`s an application that uses it. The CP2102 gives us 3V TTL to a VCP (virtual comm port) over USB as well as generating the 3. 3V needed for the board. There are a couple things to....
-
Long range FM transmitter. The power output of most of these circuits are very low because no power amplifier stages were incorporated. The transmitter circuit described here has an...
-
Fast rise-time high-voltage pulses have many uses ranging from EMC testing to device characterization. The simple, low-cost circuit described here deals with the latter. It`s able to generate 0- to 1000-V pulses with currents up to 50 A, and a rise time of....
-
Readers who do not care to modify the power supply of an old PC into a suitable halogen power source (see our April 2006 issue), may find the present design a welcome alternative. The circuit does not need any changes to the power supply. It allows the....
-
This is a low-current temperature sensors with a single-wire output. The number of pins that needed to interface with a microprocessor is minimized by this....
-
A dynamic microphone preamplifier can be realized using LM387 dual operational amplifier integrated circuit. Input impedance corresponds to 47k, it depends almost exclusively by R1. If you wish to connect a dynamic microphone with a different value, the....
-
There are two independent modeling light circuits for the P2000D - one for each of the two channels. The modeling light circuit is completely independent from the high voltage strobe circuitry - to the point of having its own On/Off switch. This means, of....
-
The following circuit shows about Noisy Regen Receiver Circuit Diagram. Features: Noisy Regenerative Receiver Circuit, making it easier to ....
-
This is the complete schematic for the circuit that is contained on the AMZ Multi-Purpose PC Board. None of the example circuits will utilize every part that has been positioned on the board. Extra parts have been included to add flexibility and options to....
-
A simple thermometer built with operational amplifiers and a normal or protective diode such as 1N4148, instead of the temperature sensor can be made using electronic diagram below. A constant reference voltage is applied to the noninverting input of....
-
PCA84C-440/441 is the single-chip microcomputer integrated circuit produced by Philips company, it is widely used in domestic and imported large screen color TV, such as Philips and other color television.1. The internal block circuit diagram and pin....
-
Many blind and deaf-blind persons use portable electronic devices to assist their everyday lives but it is difficult for them to test the batteries used in this equipment. Talking voltmeters are available but there is no equivalent usable by deaf-blind....
-
Based on NE555 this circuit turns on and off the IC output by a momentary switch. In other words it works as a mechanical latching relay, but the circuit backs to the start condition when you switch off the power supply. This feature is often required in....
-
The circuit will convert an audio and video signal into a UHF TV signal. It`s desired to connect a video signal originating from a camera or other video source to a normal TV set. The audio and video signal is converted into a UHF TV signal so. This is....
-
This circuit shows a car audio amplifier with TDA7381 IC. With the Tda7381 audio amplifier IC we can design a very simple 4x25 watts car radio ....
-
This is an automatic light dimmer circuit. You do not need to dim the lights by yourself. It is so very convenient, because we use the LDR to detect external....
-
This is design circuit for converter meter voltage to frequency. Normally we often encountered the frequency meter can be used in speed sensor, tachometer, measurement or signal recurring. This frequency to voltage converter (FVC) can be used to change the....
-
This 5 volts Switch Mode Power Supply circuit use the IC from National Semiconductor has been producing and designing ICs for use in switch-mode power supp...
-
It`s based on a Philips class-H audio amplifier IC and can deliver 36W RMS OR 70W music power, all from a 13.8V supply. Our new Mighty Midget Amplifier can really pack a punch - around 36W RMS continuous into a 4-ohm load when using a 13.8V supply. However,....
-
This little circuit can be used to dim lights up to about 350 watts. It uses a simple, standard TRIAC circuit that, in my expirience, generates very little heat. Please note that this circuit cannot be used with fluorescent lights...