- Home /
- Search about UHF TRANSCEIVER
Page 4 about UHF TRANSCEIVER | |
Total Found: 315 |
-
I have few Kenwood TK-760G-1 transceivers (two-way radios) and they all were programmed to one channel and all other features were locked. In the internet and in local newsgroup I collected various software for Kenwood programming. All I needed is....
-
The MLX90224 series are dual Hall effect Latches It includes two Hall effect latch functions of which typical thresholds are +/- 2. 0 mT. In each latch, the magnetic flux detection is performed by a switched silicon Hall plate. The BOP and BRP are....
-
This is the another UHF-TV pre-amplifier circuit diagram which simpler than the previous UHF TV preamplifier. This circuit is based MPSH10. Alternatives that could be put to use to replace MPSH10 are BF180 and BCY90. The tuned circuit comprising the 15nH....
-
This is an UHF bandage TV antenna preamplifier circuit With 15dB accretion to body easily. It is formed based on BF180 UHF Transistor. The aboriginal date is an bandage canyon clarify complete by the C1, CV1, L1, L4, C7 and C3, the additional date is a....
-
The TRF1400 VHF/UHF RZ ASK remote control receiver is specifically designed for RZ ASK (return-to-zero amplitude-shift keyed) commu- nications systems operating in the 200-MHz to 450-MHz band. This device is targeted for use in automotive and home security....
-
The Kenwood TM-733A is an older dual-band mobile radio. This radio is capable of 50 watts transmit on VHF, 35 watts on UHF, full-duplex crossband repeat, and simultaneous receive on two VHF or UHF frequencies. It does have a problem, however: It is terribly....
-
This is circuit that can be used to strengthen the RF signals from a television antenna work at UHF frequencies in the range 450-800MHz. It has a gain of around 10dB and is suitable for boosting weak TV signals The tuned circuit comprising the 15nH inductor....
-
FM Booster, Active FM Antenna Amplifier This FM booster that can be used to listen to programmes from distant FM stations clearly. The circuit comprises a common-emitter tuned RF preamplifier wired around VHF/UHF transistor 2SC2570. (Only C....
-
MC44BS373CA: PLL Tuned UHF and VHF Audio Video High Integration Modulator MC44BS373CA The MC44BS373CA Audio and Video Modulator is for use in VCRs, set-top boxes, and similar devices. By Freescale Semiconductor, Inc ..
-
Is based on the FTDI`s USB / serial IC FT-232BM. The adapter has been successfully tested with the following transceivers and software: VX-7R (VX-7R Commander), FT-8900 (FTB-8900), FT-817 (FT-817 Commander and Ham Radio Deluxe) and IC-706MkIIG (Ham Radio....
-
The NESCAF audio filter is a small and low cost circuit that works great. It is a good addition to any amateur radio setup. It is especially useful with radio receivers or transceivers that lack an optional CW filter. I have made a product review of the....
-
This circuit is useful to detect microwave (gigahertz signal) sources like microwave oven, satellite communication devices, Mobile phones etc. It gives audio visual indications when it detects the Microwaves in the Gigahertz band. Microwave is the form of EM....
-
For the transmitter schematic (part of this transceiver), see entry entitled S-W ATV Transmit-ter for 440 MHz, Fig. 5-1. The downconverter portion is shown here.This transmitter contains both a video and sound section. Five to six watts PEP on synch tips of....
-
The 6JS6C tube is a TV Deflection Tube, or "Sweep Tube". Although not meant for transmitting, it exhibits sufficient performance for RF operation through 30 MHz. Each tube can dissipate 30 watts of plate power. The base is a 12-pin socket. There will come a....
-
The LA7051 is a video, Audio signal processor IC for UHF band RF Modulator It performs the functions of Audio FM Modulator video clamp circuit, white clip circuit....
-
This project is designed for the entry level laser experimenter. The circuit allows any two computers with serial (RS-232) communication capability to communicate over 200 meters using a laser beam. A low cost transmitter only circuit is also presented here....
-
This UHF wideband signal amplifier has a total gain of 10 to 15 dB in the 400 - 850 MHz domain frequency so it can be used where the tv signal is weak. For UHF TV signal amplifier to work correctly, you need to cut the components pins as short as possible.....
-
This UHF amplifier circuit electronic project can be useful in situations where the TV signal is weak. The UHF amplifier circuit has a gain of 10-15 dB in a frequency range between 400 and 850 MHz. To obtain optimum performance and good reliability, the PCB....
-
This amplifier circuit is used to amplify TV signals in UHF range. It uses a low-noise transistor and gives 10 to 15 dB amplification in the frequency range from 400 MHz to 850 MHz. The transistor must be shielded from the input components and in....
-
In some cases, appliances and equipment are able to operate when supplied by two different levels of AC line voltage to their main terminals (120 V or 240 V). This is why, it is very common that appliances and equipment have mechanical selectors or switches....
-
AVR Microcontroller And Best-in-class 2. 4GHz RF transceiver ATMEGA128RFA1 is an IEEE 802. 15. 4 compliant single-chip, combining the industry- leading AVR Microcontroller and best-in-class 2. 4GHz RF transceiver providing industry`s highest RF performance....
-
The main characteristic of the transceiver presented below is the simplicity, but in the same time giving good performance, with a minimum investment. The radio is based on MC3362 ( buy ). This integrated circuit its an FM receiver, double conversion, which....
-
This page identifies all the hardware modifications necessary to adapt a Kenwood TK-931 transceiver for 902 MHz repeater receive operation. Not shown here is the effort required to program the radio for the desired operating frequency. This is accomplished....
-
Here`s an antenna selector, Preselector, attenuator, preamplifier accessory for every HF amateur transceiver. It can improve your receiver`s IP2 for out-of-band signals and yield good flexibility. My father, I4FAF (an old-timer) and I both very much like....
-
The original firmware is usable on the amateur radio bands, but is not very convenient to use. Wulf-Gerd, DL1FAC has developped a new firmware that is much more "ham-friendly". It is open source. With this firmware you can change the frequency as you like,....
-
This RF probe can be used at High Frequency (HF) or Ultra High Frequency (UHF) on both 50 and 75 ohm coaxial cables. In addition the RF voltage can be measured under load or no-load conditions which allows the circuit to double as an RF Watt meter. The RF....
-
No matter WHAT the label on the radio (or the seller) says, no Spectra will ever operate over the entire 136-174MHz (high band) or 403-512MHz (UHF) frequency range. Each unit will do only a portion of that band`s frequency spread, and that portion is called....